NETGEAR WAG102NA manual Restoring the WAG102 to the Factory Default Settings

Page 75

ProSafe Dual Band Wireless Access Point WAG102 Reference Manual (802.11a/g)

2.When you have located the file, click Retrieve to upload the file. After completing the upload, the WAG102 will reboot automatically.

Restoring the WAG102 to the Factory Default Settings

It is sometimes desirable to restore the wireless access point to the factory default settings. This can be done by using the Restore function, which restores all factory settings. After a restore, the wireless access point password will be password, the WAG102 DHCP client will be enabled, the default LAN IP address will be 192.168.0.232, and the access point name will reset to the name printed on the label on the bottom of the unit.

To restore the factory default configuration settings without knowing the login password or IP address, you must use the Default Reset button on the rear panel of the wireless access point (see Figure 1-1 on page 1-7). The reset button has two functions:

Reboot. When pressed and released, the Wireless Access Point will reboot (restart).

Reset to Factory Defaults. This button can also be used to clear all data and restore all settings to the factory default values.

To clear all data and restore the factory default values:

1.Power off the WAG102.

2.Use something with a small point, such as a pen, hold the Reset button for 5 seconds while your Power On the WAG102.

3.Continue holding the Reset Button until the LEDs blink twice.

4.Release the Reset Button.

The factory default configuration has now been restored and the WAG102 is ready for use.

Management

3-11

v2.0, September 2006

Image 75
Contents NETGEAR, Inc Statement of Conditions Placement and Range GuidelinesTechnical Support TrademarksFCC Requirements for Operation in the United States FCC StatementIndustry Canada Compliance Statement Europe EU Declaration of Conformity V2.0, September 36,40,44,48 Antenna Statement for the European CommunityEuropean Spectrum Usage Rules Effective April 11 Channels 1 toBestätigung des Herstellers/Importeurs Certificate of the Manufacturer/ImporterProduct and Publication Details Contents Chapter Management Appendix a Default Settings and Technical Specifications Xii Conventions, Formats and Scope About This ManualHow to Use This Manual How to Print this Manual Xvi Chapter Introduction Supported Standards and Conventions Key Features and StandardsKey Features Autosensing Ethernet Connections with Auto Uplink 802.11a/g Standards-based Wireless NetworkingSystem Requirements Compatible and Related Netgear ProductsWhat’s In the Box? Front Panel LED Indicators Hardware DescriptionFront Panel LED Description LINK/ACT LAN Rear PanelV2.0, September V2.0, September Chapter Basic Installation and Configuration Wireless Equipment Placement and Range Guidelines LUHOHVVDWD 6HFXULW\2SWLRQV Understanding WAG102 Wireless Security OptionsSetting up the WAG102 Wireless Access Point Installing the WAG102 Wireless Access PointConfiguring LAN and Wireless Access V2.0, September V2.0, September V2.0, September V2.0, September Verifying Wireless Connectivity Deploying the WAG102 Wireless Access PointLogging In Using the Default IP Address Setting Basic IP Options V2.0, September Configuring 802.11a Wireless Settings Wireless SettingsV2.0, September Configuring 802.11b/g Wireless Settings Setting Up and Testing Basic Wireless Connectivity V2.0, September Understanding Security Profiles Typea Description Network Authentication TypesType a Description Data Encryption SettingsV2.0, September 802.11a Configuration Ssid and WEP/WPA Settings Setup Form802.11b/g Configuration Configuring the Radius Server Settings V2.0, September Setting up a Security Profile V2.0, September Configuring WEP V2.0, September Configuring WPA with Radius Configuring WPA2 with Radius Click Apply to save your Radius settings Configuring WPA and WPA2 with RadiusConfiguring WPA-PSK Configuring WPA2-PSK Enter the WPA Passphrase Network Key Configuring WPA-PSK and WPA2-PSKRestricting Wireless Access by MAC Address V2.0, September Remote Management Chapter ManagementUsing Syslog and Activity Log Information General Information Fields Viewing General Summary InformationField Description V2.0, September Viewing Network Traffic Statistics Statistics Fields Viewing Available Wireless Station ListUpgrading the Wireless Access Point Software V2.0, September Saving and Retrieving the Configuration Configuration File ManagementRestoring the WAG102 to the Factory Default Settings Changing the Administrator Password Hotspot Settings Chapter Advanced ConfigurationConfiguring Advanced Wireless Settings Enabling Wireless Bridging and Repeating V2.0, September Configuring a WAG102 as a Point-to-Point Bridge Configuring a Point-to Configuring the WAG102 as a Wireless Repeater Verify the following parameters for all access points Click Apply to save your settings V2.0, September No lights are lit on the wireless access point Chapter TroubleshootingLAN light is not lit Wireless LAN activity light does not light upWhen I enter a URL or IP address I get a timeout error Cannot connect to the WAG102 to configure itUsing the Reset Button to Restore Factory Default Settings Appendix a Default Settings and Technical Specifications Factory Default SettingsTable A-1. Access Point Default Configuration Settings GMT Table A-2. WAG102 Technical Specifications Technical SpecificationsV2.0, September Document Link Appendix B Related DocumentsV2.0, September Numerics IndexIndex-2 Index-3 Index-4 Index-5 Index-6
Related manuals
Manual 8 pages 7.82 Kb