NETGEAR WAG102NA manual Configuring a WAG102 as a Point-to-Point Bridge

Page 81

ProSafe Dual Band Wireless Access Point WAG102 Reference Manual (802.11a/g)

Configuring a WAG102 as a Point-to-Point Bridge

To configure a point-to-point bridge as shown in Figure 4-4:

1.Under Advanced on the main menu, select Advanced Access Point Settings 11a or Advanced Access Point Settings 11b/g. The Advanced Access Point Settings screen will display.

Figure 4-4

2.Configure the WAG102 (AP1) on LAN Segment 1 in Point-to-Point Bridge mode.

3.Configure the WAG102 (AP2) on LAN Segment 2 in Point-to-Point Bridge mode.

AP1 must have AP2’s MAC address in its Remote MAC Address field and AP2 must have AP1’s MAC address in its Remote MAC Address field.

4.Configure and verify the following parameters for both access points:

Verify that the LAN network configuration of the WAG102 Wireless Access Points both are configured to operate in the same LAN network address range as the LAN devices

Both use the same ESSID, Channel, authentication mode, if any, and security settings if security is in use.

5.Verify connectivity across the LAN 1 and LAN 2.

A computer on either LAN segment should be able to connect to the Internet or share files and printers of any other PCs or servers connected to LAN Segment 1 or LAN Segment 2.

6.Click Apply to save your settings.

Advanced Configuration

4-5

v2.0, September 2006

Image 81
Contents NETGEAR, Inc Technical Support Placement and Range GuidelinesTrademarks Statement of ConditionsFCC Requirements for Operation in the United States FCC StatementIndustry Canada Compliance Statement Europe EU Declaration of Conformity V2.0, September European Spectrum Usage Rules Effective April 11 Antenna Statement for the European CommunityChannels 1 to 36,40,44,48Bestätigung des Herstellers/Importeurs Certificate of the Manufacturer/ImporterProduct and Publication Details Contents Chapter Management Appendix a Default Settings and Technical Specifications Xii Conventions, Formats and Scope About This ManualHow to Use This Manual How to Print this Manual Xvi Chapter Introduction Supported Standards and Conventions Key Features and StandardsKey Features Autosensing Ethernet Connections with Auto Uplink 802.11a/g Standards-based Wireless NetworkingSystem Requirements Compatible and Related Netgear ProductsWhat’s In the Box? Front Panel LED Indicators Hardware DescriptionFront Panel LED Description LINK/ACT LAN Rear PanelV2.0, September V2.0, September Chapter Basic Installation and Configuration Wireless Equipment Placement and Range Guidelines LUHOHVVDWD 6HFXULW\2SWLRQV Understanding WAG102 Wireless Security OptionsSetting up the WAG102 Wireless Access Point Installing the WAG102 Wireless Access PointConfiguring LAN and Wireless Access V2.0, September V2.0, September V2.0, September V2.0, September Verifying Wireless Connectivity Deploying the WAG102 Wireless Access PointLogging In Using the Default IP Address Setting Basic IP Options V2.0, September Configuring 802.11a Wireless Settings Wireless SettingsV2.0, September Configuring 802.11b/g Wireless Settings Setting Up and Testing Basic Wireless Connectivity V2.0, September Understanding Security Profiles Typea Description Network Authentication TypesType a Description Data Encryption SettingsV2.0, September 802.11a Configuration Ssid and WEP/WPA Settings Setup Form802.11b/g Configuration Configuring the Radius Server Settings V2.0, September Setting up a Security Profile V2.0, September Configuring WEP V2.0, September Configuring WPA with Radius Configuring WPA2 with Radius Click Apply to save your Radius settings Configuring WPA and WPA2 with RadiusConfiguring WPA-PSK Configuring WPA2-PSK Enter the WPA Passphrase Network Key Configuring WPA-PSK and WPA2-PSKRestricting Wireless Access by MAC Address V2.0, September Remote Management Chapter ManagementUsing Syslog and Activity Log Information General Information Fields Viewing General Summary InformationField Description V2.0, September Viewing Network Traffic Statistics Statistics Fields Viewing Available Wireless Station ListUpgrading the Wireless Access Point Software V2.0, September Saving and Retrieving the Configuration Configuration File ManagementRestoring the WAG102 to the Factory Default Settings Changing the Administrator Password Hotspot Settings Chapter Advanced ConfigurationConfiguring Advanced Wireless Settings Enabling Wireless Bridging and Repeating V2.0, September Configuring a WAG102 as a Point-to-Point Bridge Configuring a Point-to Configuring the WAG102 as a Wireless Repeater Verify the following parameters for all access points Click Apply to save your settings V2.0, September No lights are lit on the wireless access point Chapter TroubleshootingLAN light is not lit Wireless LAN activity light does not light upWhen I enter a URL or IP address I get a timeout error Cannot connect to the WAG102 to configure itUsing the Reset Button to Restore Factory Default Settings Appendix a Default Settings and Technical Specifications Factory Default SettingsTable A-1. Access Point Default Configuration Settings GMT Table A-2. WAG102 Technical Specifications Technical SpecificationsV2.0, September Document Link Appendix B Related DocumentsV2.0, September Numerics IndexIndex-2 Index-3 Index-4 Index-5 Index-6
Related manuals
Manual 8 pages 7.82 Kb