NETGEAR WAG102NA manual Industry Canada Compliance Statement

Page 4

ProSafe Dual Band Wireless Access Point WAG102 Reference Manual (802.11a/g)

RF Exposure Warning for North America, and Australia

Warning! To meet FCC and other national safety guidelines for RF exposure, the antennas for this device (see below) must be installed to ensure a minimum separation distance of 20cm (7.9 in.) from persons. Further, the antennas shall not be collocated with other antenna or radio transmitter.

Antenna Statement for North America and Australia

In addition to its own 2 antennas, the WAG102 device has been approved for use with the following detachable antennas and antenna cables:

Approved	Antenna Gain and	Approved Antenna	Antenna Cable	Maximum
Antennas	type	Cable	Length	Transmitted Power
NETGEAR	18 dBi, directional	NETGEAR ACC-10314-	1.5 m to 30 m	19 dBm + 18 dBi ant.
ANT24D18	outdoor/indoor	01 thru 05

NETGEAR	9 dBi, omnidirectional	NETGEAR ACC-10314-	1.5 m to 30 m	19 dBm + 9 dBi ant.
ANT2409	outdoor/indoor	01 thru 05

NETGEAR	5 dBi, ceiling/wall	NETGEAR ACC-10314-	1.5 m to 30 m	19 dBm + 5 dBi ant.
ANT24O5	indoor	01 thru 05

*WG302 maximum radiated power in North America and Australia: 20 dBm – cable loss + antenna gain

Please go to www.netgear.com/go/wag102_fcc for an updated list of wireless accessories approved to be used with the WAG102 in North America and Australia.

Industry Canada Compliance Statement

This Class B Digital apparatus meets all the requirements of the Canadian Interference Causing Equipment Regulations ICES 003.

Cet appareil numerique de classe B respecte les exigences du reglement du Canada sur le materiel brouilleur NMB-003.

The device is certified to the requirements of RSS-210 for 2.4 GHz spread spectrum devices. The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations. For further information, contact your local Industry Canada office.

iv

v2.0, September 2006

Image 4

Contents NETGEAR, Inc Placement and Range Guidelines Technical SupportTrademarks Statement of ConditionsFCC Statement FCC Requirements for Operation in the United StatesIndustry Canada Compliance Statement Europe EU Declaration of Conformity V2.0, September Antenna Statement for the European Community European Spectrum Usage Rules Effective April 11Channels 1 to 36,40,44,48Certificate of the Manufacturer/Importer Bestätigung des Herstellers/ImporteursProduct and Publication Details Contents Chapter Management Appendix a Default Settings and Technical Specifications Xii About This Manual Conventions, Formats and ScopeHow to Use This Manual How to Print this Manual Xvi Chapter Introduction Key Features and Standards Supported Standards and ConventionsKey Features 802.11a/g Standards-based Wireless Networking Autosensing Ethernet Connections with Auto UplinkCompatible and Related Netgear Products System RequirementsWhat’s In the Box? Hardware Description Front Panel LED IndicatorsFront Panel Rear Panel LED Description LINK/ACT LANV2.0, September V2.0, September Chapter Basic Installation and Configuration Wireless Equipment Placement and Range Guidelines Understanding WAG102 Wireless Security Options LUHOHVVDWD 6HFXULW\2SWLRQVInstalling the WAG102 Wireless Access Point Setting up the WAG102 Wireless Access PointConfiguring LAN and Wireless Access V2.0, September V2.0, September V2.0, September V2.0, September Deploying the WAG102 Wireless Access Point Verifying Wireless ConnectivityLogging In Using the Default IP Address Setting Basic IP Options V2.0, September Wireless Settings Configuring 802.11a Wireless SettingsV2.0, September Configuring 802.11b/g Wireless Settings Setting Up and Testing Basic Wireless Connectivity V2.0, September Understanding Security Profiles Network Authentication Types Typea DescriptionData Encryption Settings Type a DescriptionV2.0, September Ssid and WEP/WPA Settings Setup Form 802.11a Configuration802.11b/g Configuration Configuring the Radius Server Settings V2.0, September Setting up a Security Profile V2.0, September Configuring WEP V2.0, September Configuring WPA with Radius Configuring WPA2 with Radius Configuring WPA and WPA2 with Radius Click Apply to save your Radius settingsConfiguring WPA-PSK Configuring WPA2-PSK Configuring WPA-PSK and WPA2-PSK Enter the WPA Passphrase Network KeyRestricting Wireless Access by MAC Address V2.0, September Chapter Management Remote ManagementUsing Syslog and Activity Log Information Viewing General Summary Information General Information FieldsField Description V2.0, September Viewing Network Traffic Statistics Viewing Available Wireless Station List Statistics FieldsUpgrading the Wireless Access Point Software V2.0, September Configuration File Management Saving and Retrieving the ConfigurationRestoring the WAG102 to the Factory Default Settings Changing the Administrator Password Chapter Advanced Configuration Hotspot SettingsConfiguring Advanced Wireless Settings Enabling Wireless Bridging and Repeating V2.0, September Configuring a WAG102 as a Point-to-Point Bridge Configuring a Point-to Configuring the WAG102 as a Wireless Repeater Verify the following parameters for all access points Click Apply to save your settings V2.0, September Chapter Troubleshooting No lights are lit on the wireless access pointWireless LAN activity light does not light up LAN light is not litCannot connect to the WAG102 to configure it When I enter a URL or IP address I get a timeout errorUsing the Reset Button to Restore Factory Default Settings Factory Default Settings Appendix a Default Settings and Technical SpecificationsTable A-1. Access Point Default Configuration Settings GMT Technical Specifications Table A-2. WAG102 Technical SpecificationsV2.0, September Appendix B Related Documents Document LinkV2.0, September Index NumericsIndex-2 Index-3 Index-4 Index-5 Index-6

Related manuals

Manual 8 pages 7.82 Kb