NETGEAR WG602V4 manual Technical Support, Placement and Range Guidelines

Page 2

Technical Support

Please register to obtain technical support. Please retain your proof of purchase and warranty information.

To register your product, get product support or obtain product information and product documentation, go to www.netgear.com. If you do not have access to the World Wide Web, you can register your product by filling out the registration card and mailing it to NETGEAR customer service.

You will find technical support information at:

www.netgear.com/support/main.asp through the customer service area. If you want to contact technical support by telephone, see the support information card for the correct telephone number for your country.

© 2007 by NETGEAR, Inc. All rights reserved.

Trademarks

NETGEAR and the NETGEAR logo are registered trademarks of NETGEAR, Inc. Windows is a registered trademark of Microsoft Corporation. Other brand and product names are trademarks or registered trademarks of their respective holders. Information is subject to change without notice. All rights reserved.

Statement of Conditions

In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice

NETGEAR WG602v4 54 Mbps Wireless Access Point

Tested to Comply with FCC Standards

FOR HOME OR OFFICE USE

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired operation.

Placement and Range Guidelines

Indoors, computers can connect over 802.11 wireless networks at a maximum range of 500 feet (152.4 m) for 802.11b devices. However, the operating distance or range of your wireless connection can vary significantly, based on the physical placement of the wireless access point.

For best results, identify a location for your wireless access point according to these guidelines:

Away from potential sources of interference, such as PCs, large metal surfaces, microwaves, and 2.4 GHz cordless phones.

In an elevated location such as a high shelf that is near the center of the wireless coverage area for all mobile devices.

ii

1.0, June 2007

Image 2
Contents NETGEAR, Inc Placement and Range Guidelines Technical SupportFCC Statement FCC Requirements for Operation in the United StatesIndustry Canada Compliance Statement Bestätigung des Herstellers/Importeurs Certificate of the Manufacturer/Importer Contents Chapter Management Appendix B Related Documents Index Page About This Manual Audience, Scope, Conventions, and FormatsHow to Use This Manual How to Print this ManualRevision History Page Support for Standards About the Netgear WG602v4 54 Mbps Wireless Access PointChapter Introduction Key Features Access Point ModeAutosensing Ethernet Connections with Auto Uplink 802.11b/g Standards-based Wireless NetworkingWireless Multimedia WMM Support Compatible and Related Netgear ProductsWhat’s In the Box? Hardware DescriptionWG602v4 Wireless Access Point Front Panel Front Panel LED DescriptionWG602v4 Wireless Access Point Rear Panel Chapter Installation and Configuration Placement and Range GuidelinesBasic Setup and Installation System RequirementsInstalling the WG602v4 Selecting Basic IP Settings OptionsV1.0, June V1.0, June V1.0, June V1.0, June Verifying Wireless Connectivity Deploying the Wireless APIP Address Login Logging Into the WG602v4NetBIOS Name Login NETGEAR123456 Wireless Security Options Range Up to 300 Foot RadiusConfiguring Wireless Security WEP Security Encryption Key Wireless Settings Information Form If WPA-PSK or WPA2-PSK Authentication is UsedConfiguring WEP Wireless Security Configuring WPA-PSK Wireless Security Configuring WPA2-PSK Wireless Security Configuring WPA-PSK/WPA2-PSK Wireless SecurityRestricting Wireless Access by MAC Address V1.0, June V1.0, June V1.0, June Chapter Management Viewing General InformationViewing a List of Attached Devices General Information FieldsUpgrading the Wireless Access Point Software To view the Station ListRebooting and Resetting Factory Defaults Rebooting the Wireless AP Restoring Factory Default SettingsChanging the Administrator Password Configuring a WG602v4 as a Point-to-Point Bridge Chapter Advanced ConfigurationConfiguring Access Point Modes Advanced Configuration AP1 AP2 SegmentConfiguring Wireless Multi-Point Bridging V1.0, June AP2 AP3 Configuring Repeater with Wireless Client Association Click Apply to save your changes Wireless PC Associated with AP1 Client Mode Configuration Check the Client Mode radio boxV1.0, June V1.0, June Site Survey Fields Field DescriptionAdvanced Wireless Settings WG602v4 AP Mode WG602v4 inInternet Client ModeMake any changes and click Apply to save your settings V1.0, June No lights are lit on the access point Chapter TroubleshootingTroubleshooting Ethernet LAN light is not litWireless LAN activity light is not lit Cannot configure the wireless access point from a browserUsing the Reset Button to Restore Factory Default Settings When I enter a URL or IP address I get a timeout errorV1.0, June Default Configuration Settings Table A-1. Access Point Default Configuration SettingsTechnical Specifications Table A-2. Technical SpecificationsVcci V1.0, June Appendix B Related Documents Document LinkV1.0, June Index NumericsIndex-2 Index-3 Index-4
Related manuals
Manual 2 pages 27.86 Kb