NETGEAR WG602V4 manual Client Mode Configuration, Check the Client Mode radio box

Page 58

NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Manual

Client Mode Configuration

In Client Mode, the WG602v4 will operate as a Client bridge only and send traffic to the remote AP (Infrastructure Mode) or peer device (Ad-Hoc mode):

•Infrastructures – In this mode, the WG602v4 operates as a wireless client bridge that can only connect and send traffic to an access point.

•Ad-Hoc– In this mode, the WG602v4 communicates on a peer-to-peer basis. There is no structure of fixed points in the network.

The default mode for the WG602v4 is Infrastructure. However, no matter which mode is selected, you must reconfigure the device after reboot. Once Client Mode is enabled, all of the existing wireless access point settings are erased.

To enable and configure Client Mode:

1.Using your Web browser, log in to the WG602v4 using your selected method of login.

Figure 4-7

2.Under Advanced on the main menu, click Wireless Bridging. The Wireless Bridging screen will display.

3.Check the Client Mode radio box.

4-10	Advanced Configuration

v1.0, June 2007

Image 58

Contents NETGEAR, Inc Placement and Range Guidelines Technical SupportFCC Statement FCC Requirements for Operation in the United StatesIndustry Canada Compliance Statement Bestätigung des Herstellers/Importeurs Certificate of the Manufacturer/Importer Contents Chapter Management Appendix B Related Documents Index Page About This Manual Audience, Scope, Conventions, and FormatsHow to Use This Manual How to Print this ManualRevision History Page Chapter Introduction About the Netgear WG602v4 54 Mbps Wireless Access PointSupport for Standards Key Features Access Point ModeAutosensing Ethernet Connections with Auto Uplink 802.11b/g Standards-based Wireless NetworkingWireless Multimedia WMM Support Compatible and Related Netgear ProductsWhat’s In the Box? Hardware DescriptionWG602v4 Wireless Access Point Front Panel Front Panel LED DescriptionWG602v4 Wireless Access Point Rear Panel Chapter Installation and Configuration Placement and Range GuidelinesBasic Setup and Installation System RequirementsInstalling the WG602v4 Selecting Basic IP Settings OptionsV1.0, June V1.0, June V1.0, June V1.0, June Verifying Wireless Connectivity Deploying the Wireless APIP Address Login Logging Into the WG602v4NetBIOS Name Login NETGEAR123456 Wireless Security Options Range Up to 300 Foot RadiusConfiguring Wireless Security WEP Security Encryption Key Wireless Settings Information Form If WPA-PSK or WPA2-PSK Authentication is UsedConfiguring WEP Wireless Security Configuring WPA-PSK Wireless Security Configuring WPA2-PSK Wireless Security Configuring WPA-PSK/WPA2-PSK Wireless SecurityRestricting Wireless Access by MAC Address V1.0, June V1.0, June V1.0, June Chapter Management Viewing General InformationViewing a List of Attached Devices General Information FieldsUpgrading the Wireless Access Point Software To view the Station ListRebooting and Resetting Factory Defaults Rebooting the Wireless AP Restoring Factory Default SettingsChanging the Administrator Password Configuring Access Point Modes Chapter Advanced ConfigurationConfiguring a WG602v4 as a Point-to-Point Bridge Advanced Configuration AP1 AP2 SegmentConfiguring Wireless Multi-Point Bridging V1.0, June AP2 AP3 Configuring Repeater with Wireless Client Association Click Apply to save your changes Wireless PC Associated with AP1 Client Mode Configuration Check the Client Mode radio boxV1.0, June V1.0, June Site Survey Fields Field DescriptionAdvanced Wireless Settings WG602v4 AP Mode WG602v4 inInternet Client ModeMake any changes and click Apply to save your settings V1.0, June No lights are lit on the access point Chapter TroubleshootingTroubleshooting Ethernet LAN light is not litWireless LAN activity light is not lit Cannot configure the wireless access point from a browserUsing the Reset Button to Restore Factory Default Settings When I enter a URL or IP address I get a timeout errorV1.0, June Default Configuration Settings Table A-1. Access Point Default Configuration SettingsTechnical Specifications Table A-2. Technical SpecificationsVcci V1.0, June Appendix B Related Documents Document LinkV1.0, June Index NumericsIndex-2 Index-3 Index-4

Related manuals

Manual 2 pages 27.86 Kb