NETGEAR WG602V4 Wireless Settings Information Form, If WPA-PSK or WPA2-PSK Authentication is Used

Page 35

NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Manual

Wireless Settings Information Form

Before customizing your wireless settings, print this form and record the following information. (If you are working with an existing wireless network, the person who set up or is responsible for the network will be able to provide this information.) After you record the settings for your wireless network, store this form in a safe place.

Wireless Network Name (SSID): ______________________________ The SSID, identifies the wireless network. You can use up to 32 alphanumeric characters. The SSID is case sensitive. The SSID in the wireless adapter card must match the SSID of the wireless access point. In some configuration utilities (such as in Windows XP), the term “wireless network name” is used instead of SSID.

If WEP Authentication is Used. Circle one: Open System, Shared Key, or Mix.

Note: If you select Shared Key, the other devices in the network will not connect unless they are set to Shared Key as well and are configured with the correct key.

WEP Encryption key size. Choose one: 64-bitor 128-bit. Again, the encryption key size must be the same for the wireless adapters and the wireless access point.

Data Encryption (WEP) Keys. There are two methods for creating WEP data encryption keys. Whichever method you use, record the key values in the spaces below.

Passphrase method. ______________________________ These characters are case sensitive. Enter a word or group of printable characters and click the Generate Keys button. Not all wireless devices support the passphrase method.

Manual method. These values are not case sensitive. For 64-bit WEP, enter 10 hex digits (any combination of 0-9 or a-f). For 128-bit WEP, enter 26 hex digits.

Key 1: ___________________________________

Key 2: ___________________________________

Key 3: ___________________________________

Key 4: ___________________________________

If WPA-PSK or WPA2-PSK Authentication is Used.

WPA Passphrase: ______________________________

WPA2 Passphrase: ______________________________

These characters are case sensitive. Enter a word or group of printable characters. When you use WPA-PSK or WPA2-PSK, the other devices in the network will not connect unless they are set to WPA-PSK or WPA2-PSK as well and are configured with the correct Passphrase.

Installation and Configuration

2-15

v1.0, June 2007

Image 35
Contents NETGEAR, Inc Technical Support Placement and Range GuidelinesFCC Requirements for Operation in the United States FCC StatementIndustry Canada Compliance Statement Bestätigung des Herstellers/Importeurs Certificate of the Manufacturer/Importer Contents Chapter Management Appendix B Related Documents Index Page Audience, Scope, Conventions, and Formats About This ManualHow to Print this Manual How to Use This ManualRevision History Page Support for Standards About the Netgear WG602v4 54 Mbps Wireless Access PointChapter Introduction Access Point Mode Key FeaturesCompatible and Related Netgear Products 802.11b/g Standards-based Wireless NetworkingWireless Multimedia WMM Support Autosensing Ethernet Connections with Auto UplinkHardware Description What’s In the Box?Front Panel LED Description WG602v4 Wireless Access Point Front PanelWG602v4 Wireless Access Point Rear Panel Placement and Range Guidelines Chapter Installation and ConfigurationSystem Requirements Basic Setup and InstallationSelecting Basic IP Settings Options Installing the WG602v4V1.0, June V1.0, June V1.0, June V1.0, June Deploying the Wireless AP Verifying Wireless ConnectivityLogging Into the WG602v4 IP Address LoginNetBIOS Name Login NETGEAR123456 Range Up to 300 Foot Radius Wireless Security OptionsConfiguring Wireless Security WEP Security Encryption Key If WPA-PSK or WPA2-PSK Authentication is Used Wireless Settings Information FormConfiguring WEP Wireless Security Configuring WPA-PSK Wireless Security Configuring WPA-PSK/WPA2-PSK Wireless Security Configuring WPA2-PSK Wireless SecurityRestricting Wireless Access by MAC Address V1.0, June V1.0, June V1.0, June Viewing General Information Chapter ManagementGeneral Information Fields Viewing a List of Attached DevicesTo view the Station List Upgrading the Wireless Access Point SoftwareRebooting and Resetting Factory Defaults Restoring Factory Default Settings Rebooting the Wireless APChanging the Administrator Password Configuring a WG602v4 as a Point-to-Point Bridge Chapter Advanced ConfigurationConfiguring Access Point Modes Advanced Configuration Segment AP1 AP2Configuring Wireless Multi-Point Bridging V1.0, June AP2 AP3 Configuring Repeater with Wireless Client Association Click Apply to save your changes Wireless PC Associated with AP1 Check the Client Mode radio box Client Mode ConfigurationV1.0, June V1.0, June Field Description Site Survey FieldsWG602v4 AP Mode WG602v4 inInternet Client Mode Advanced Wireless SettingsMake any changes and click Apply to save your settings V1.0, June Ethernet LAN light is not lit Chapter TroubleshootingTroubleshooting No lights are lit on the access pointCannot configure the wireless access point from a browser Wireless LAN activity light is not litWhen I enter a URL or IP address I get a timeout error Using the Reset Button to Restore Factory Default SettingsV1.0, June Table A-1. Access Point Default Configuration Settings Default Configuration SettingsTable A-2. Technical Specifications Technical SpecificationsVcci V1.0, June Document Link Appendix B Related DocumentsV1.0, June Numerics IndexIndex-2 Index-3 Index-4
Related manuals
Manual 2 pages 27.86 Kb