NETGEAR WG602V4 manual V1.0, June

Page 53

NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Manual

.

Figure 4-3

2.Under Advanced on the main menu, click Wireless Bridging. The Wireless Bridging screen will display showing the default settings for the wireless access point.

3.Select the Wireless Multi-Point Bridging radio button to enable multi-point bridging.

4.Enter the MAC address of the first wireless access point and click Add. The AP’s MAC address and connection information will appear in the Wireless Accept Point List.

You can add wireless access points to the list for a total of four. (These wireless access points must be configured for Multi-Point Bridging.)

Advanced Configuration

4-5

v1.0, June 2007

Image 53

Contents NETGEAR, Inc Technical Support Placement and Range GuidelinesFCC Requirements for Operation in the United States FCC StatementIndustry Canada Compliance Statement Bestätigung des Herstellers/Importeurs Certificate of the Manufacturer/Importer Contents Chapter Management Appendix B Related Documents Index Page Audience, Scope, Conventions, and Formats About This ManualHow to Print this Manual How to Use This ManualRevision History Page Support for Standards About the Netgear WG602v4 54 Mbps Wireless Access PointChapter Introduction Access Point Mode Key FeaturesWireless Multimedia WMM Support 802.11b/g Standards-based Wireless NetworkingAutosensing Ethernet Connections with Auto Uplink Compatible and Related Netgear ProductsHardware Description What’s In the Box?Front Panel LED Description WG602v4 Wireless Access Point Front PanelWG602v4 Wireless Access Point Rear Panel Placement and Range Guidelines Chapter Installation and ConfigurationSystem Requirements Basic Setup and InstallationSelecting Basic IP Settings Options Installing the WG602v4V1.0, June V1.0, June V1.0, June V1.0, June Deploying the Wireless AP Verifying Wireless ConnectivityLogging Into the WG602v4 IP Address LoginNetBIOS Name Login NETGEAR123456 Range Up to 300 Foot Radius Wireless Security OptionsConfiguring Wireless Security WEP Security Encryption Key If WPA-PSK or WPA2-PSK Authentication is Used Wireless Settings Information FormConfiguring WEP Wireless Security Configuring WPA-PSK Wireless Security Configuring WPA-PSK/WPA2-PSK Wireless Security Configuring WPA2-PSK Wireless SecurityRestricting Wireless Access by MAC Address V1.0, June V1.0, June V1.0, June Viewing General Information Chapter ManagementGeneral Information Fields Viewing a List of Attached DevicesTo view the Station List Upgrading the Wireless Access Point SoftwareRebooting and Resetting Factory Defaults Restoring Factory Default Settings Rebooting the Wireless APChanging the Administrator Password Configuring a WG602v4 as a Point-to-Point Bridge Chapter Advanced ConfigurationConfiguring Access Point Modes Advanced Configuration Segment AP1 AP2Configuring Wireless Multi-Point Bridging V1.0, June AP2 AP3 Configuring Repeater with Wireless Client Association Click Apply to save your changes Wireless PC Associated with AP1 Check the Client Mode radio box Client Mode ConfigurationV1.0, June V1.0, June Field Description Site Survey FieldsWG602v4 AP Mode WG602v4 inInternet Client Mode Advanced Wireless SettingsMake any changes and click Apply to save your settings V1.0, June Troubleshooting Chapter TroubleshootingNo lights are lit on the access point Ethernet LAN light is not litCannot configure the wireless access point from a browser Wireless LAN activity light is not litWhen I enter a URL or IP address I get a timeout error Using the Reset Button to Restore Factory Default SettingsV1.0, June Table A-1. Access Point Default Configuration Settings Default Configuration SettingsTable A-2. Technical Specifications Technical SpecificationsVcci V1.0, June Document Link Appendix B Related DocumentsV1.0, June Numerics IndexIndex-2 Index-3 Index-4

Related manuals

Manual 2 pages 27.86 Kb