NETGEAR WG602V4 manual Wireless LAN activity light is not lit

Page 66

NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Manual

•Make sure the cable connectors are securely plugged in at the access point and the network device (hub, switch, or router).

•Make sure the connected device is turned on.

•Be sure the correct cable is used. Use a standard Category 5 Ethernet patch cable. If the network device has Auto Uplink™ (MDI/MDIX) ports, you may use a cross-over cable. See the Reference Manual for a full explanation of cable types.

The Wireless LAN activity light is not lit.

The wireless access point’s antenna is not working.

•If the Wireless LAN activity light stays off, disconnect the adapter from its power source and then plug it in again.

•Make sure the antenna is tightly connected to the WG602v4.

•Contact NETGEAR if the Wireless LAN light remains off.

I cannot configure the wireless access point from a browser.

Check these items:

•The WG602v4 is properly installed, LAN connections are OK, and it is powered on. Check that the LAN port LED is amber or green to verify that the Ethernet connection is OK.

•If you are using the NetBIOS name of the WG602v4 to connect, ensure that your PC and the WG602v4 are on the same network segment or that there is a WINS server on your network.

•If your PC uses a Fixed (Static) IP address, ensure that it is using an IP Address in the range of the WG602v4. The WG602v4 default IP Address is 192.168.0.227 and the default Subnet Mask is 255.255.255.0. If you are not sure about these settings, follow the instructions for “Basic Setup and Installation” on page 2-2.

I cannot access the Internet or the LAN with a wireless capable computer.

There is a configuration problem. Check these items:

•You may not have restarted the computer with the wireless adapter to have TCP/IP changes take effect. Restart the computer.

5-2	Troubleshooting

v1.0, June 2007

Image 66

Contents NETGEAR, Inc Placement and Range Guidelines Technical SupportFCC Statement FCC Requirements for Operation in the United StatesIndustry Canada Compliance Statement Bestätigung des Herstellers/Importeurs Certificate of the Manufacturer/Importer Contents Chapter Management Appendix B Related Documents Index Page About This Manual Audience, Scope, Conventions, and FormatsHow to Use This Manual How to Print this ManualRevision History Page About the Netgear WG602v4 54 Mbps Wireless Access Point Chapter IntroductionSupport for Standards Key Features Access Point ModeAutosensing Ethernet Connections with Auto Uplink 802.11b/g Standards-based Wireless NetworkingWireless Multimedia WMM Support Compatible and Related Netgear ProductsWhat’s In the Box? Hardware DescriptionWG602v4 Wireless Access Point Front Panel Front Panel LED DescriptionWG602v4 Wireless Access Point Rear Panel Chapter Installation and Configuration Placement and Range GuidelinesBasic Setup and Installation System RequirementsInstalling the WG602v4 Selecting Basic IP Settings OptionsV1.0, June V1.0, June V1.0, June V1.0, June Verifying Wireless Connectivity Deploying the Wireless APIP Address Login Logging Into the WG602v4NetBIOS Name Login NETGEAR123456 Wireless Security Options Range Up to 300 Foot RadiusConfiguring Wireless Security WEP Security Encryption Key Wireless Settings Information Form If WPA-PSK or WPA2-PSK Authentication is UsedConfiguring WEP Wireless Security Configuring WPA-PSK Wireless Security Configuring WPA2-PSK Wireless Security Configuring WPA-PSK/WPA2-PSK Wireless SecurityRestricting Wireless Access by MAC Address V1.0, June V1.0, June V1.0, June Chapter Management Viewing General InformationViewing a List of Attached Devices General Information FieldsUpgrading the Wireless Access Point Software To view the Station ListRebooting and Resetting Factory Defaults Rebooting the Wireless AP Restoring Factory Default SettingsChanging the Administrator Password Chapter Advanced Configuration Configuring Access Point ModesConfiguring a WG602v4 as a Point-to-Point Bridge Advanced Configuration AP1 AP2 SegmentConfiguring Wireless Multi-Point Bridging V1.0, June AP2 AP3 Configuring Repeater with Wireless Client Association Click Apply to save your changes Wireless PC Associated with AP1 Client Mode Configuration Check the Client Mode radio boxV1.0, June V1.0, June Site Survey Fields Field DescriptionAdvanced Wireless Settings WG602v4 AP Mode WG602v4 inInternet Client ModeMake any changes and click Apply to save your settings V1.0, June No lights are lit on the access point Chapter TroubleshootingTroubleshooting Ethernet LAN light is not litWireless LAN activity light is not lit Cannot configure the wireless access point from a browserUsing the Reset Button to Restore Factory Default Settings When I enter a URL or IP address I get a timeout errorV1.0, June Default Configuration Settings Table A-1. Access Point Default Configuration SettingsTechnical Specifications Table A-2. Technical SpecificationsVcci V1.0, June Appendix B Related Documents Document LinkV1.0, June Index NumericsIndex-2 Index-3 Index-4

Related manuals

Manual 2 pages 27.86 Kb