NETGEAR WG602V4 manual WG602v4 Wireless Access Point Rear Panel

Page 20

NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Manual

WG602v4 Wireless Access Point Rear Panel

Figure 1-2illustrates the rear layout of the WG602v4Wireless Access Point.

Power			RJ-45 Ethernet	Detachable
	Reset/Restore
Socket	Button		Port	Antenna

Figure 1-2

•Power Socket. Power adapter and cord socket for connecting the WG602v4 to an AC outlet.

•Reset and Restore Button. Restores the WG602v4 to the factory default settings when pushed and held for 10 seconds. When pushed once, the WG602v4 is reset to the previous settings.

•RJ-45 Ethernet Port. Ethernet cable port for connecting the WG602v4 to an Ethernet LAN device such as a hub, switch, or router.

•Detachable Antenna. The WG602v4 includes a detachable antenna. Be sure the antenna is securely fastened.

1-6	Introduction

v1.0, June 2007

Image 20

Contents NETGEAR, Inc Placement and Range Guidelines Technical SupportFCC Statement FCC Requirements for Operation in the United StatesIndustry Canada Compliance Statement Bestätigung des Herstellers/Importeurs Certificate of the Manufacturer/Importer Contents Chapter Management Appendix B Related Documents Index Page About This Manual Audience, Scope, Conventions, and FormatsHow to Use This Manual How to Print this ManualRevision History Page Support for Standards About the Netgear WG602v4 54 Mbps Wireless Access PointChapter Introduction Key Features Access Point Mode802.11b/g Standards-based Wireless Networking Wireless Multimedia WMM SupportAutosensing Ethernet Connections with Auto Uplink Compatible and Related Netgear ProductsWhat’s In the Box? Hardware DescriptionWG602v4 Wireless Access Point Front Panel Front Panel LED DescriptionWG602v4 Wireless Access Point Rear Panel Chapter Installation and Configuration Placement and Range GuidelinesBasic Setup and Installation System RequirementsInstalling the WG602v4 Selecting Basic IP Settings OptionsV1.0, June V1.0, June V1.0, June V1.0, June Verifying Wireless Connectivity Deploying the Wireless APIP Address Login Logging Into the WG602v4NetBIOS Name Login NETGEAR123456 Wireless Security Options Range Up to 300 Foot RadiusConfiguring Wireless Security WEP Security Encryption Key Wireless Settings Information Form If WPA-PSK or WPA2-PSK Authentication is UsedConfiguring WEP Wireless Security Configuring WPA-PSK Wireless Security Configuring WPA2-PSK Wireless Security Configuring WPA-PSK/WPA2-PSK Wireless SecurityRestricting Wireless Access by MAC Address V1.0, June V1.0, June V1.0, June Chapter Management Viewing General InformationViewing a List of Attached Devices General Information FieldsUpgrading the Wireless Access Point Software To view the Station ListRebooting and Resetting Factory Defaults Rebooting the Wireless AP Restoring Factory Default SettingsChanging the Administrator Password Configuring a WG602v4 as a Point-to-Point Bridge Chapter Advanced ConfigurationConfiguring Access Point Modes Advanced Configuration AP1 AP2 SegmentConfiguring Wireless Multi-Point Bridging V1.0, June AP2 AP3 Configuring Repeater with Wireless Client Association Click Apply to save your changes Wireless PC Associated with AP1 Client Mode Configuration Check the Client Mode radio boxV1.0, June V1.0, June Site Survey Fields Field DescriptionAdvanced Wireless Settings WG602v4 AP Mode WG602v4 inInternet Client ModeMake any changes and click Apply to save your settings V1.0, June Chapter Troubleshooting TroubleshootingNo lights are lit on the access point Ethernet LAN light is not litWireless LAN activity light is not lit Cannot configure the wireless access point from a browserUsing the Reset Button to Restore Factory Default Settings When I enter a URL or IP address I get a timeout errorV1.0, June Default Configuration Settings Table A-1. Access Point Default Configuration SettingsTechnical Specifications Table A-2. Technical SpecificationsVcci V1.0, June Appendix B Related Documents Document LinkV1.0, June Index NumericsIndex-2 Index-3 Index-4

Related manuals

Manual 2 pages 27.86 Kb