NETGEAR WG602V4 manual Table A-2. Technical Specifications

Page 70

NETGEAR 54 Mbps Wireless Access Point WG602v4 Reference Manual

Table A-1. Access Point Default Configuration Settings

Feature		Description

Wireless

	Wireless Communication	Enabled

	Wireless Network Name (SSID)	NETGEAR

	Security	Disabled

	Broadcast SSID	Enabled

	Transmission Speed	Autoa

	Country/Region	United States (in North America; otherwise, varies by
		region)
	RF Channel	11 until the region is selected

	Operating Mode	802.11b/802.11g

	Data Rate	Best
	Output Power	Full
	Access Point Mode	Access Point
	Wireless Card Access List	All wireless stations allowed
	MAC Address Filtering	Disabled

	WMM Support	Disabled
	Spanning Tree Protocol	Enabled

a. Maximum Wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate.

Technical Specifications

The following table lists the specifications for the WG602v4.

Table A-2. Technical Specifications

Parameter	NETGEAR WG602v4 54 Mbps Wireless Access Point

Radio Data Rates	1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54 Mbps Auto Rate Sensing

Frequency	2.4-2.5Ghz

Data Encoding:	Direct Sequence Spread Spectrum (DSSS) for 802.11b and Orthogonal
	Frequency Division Multiplexing (OFDM) for 802.11g


A-2	Default Configuration and Technical Specifications

v1.0, June 2007

Image 70

Contents NETGEAR, Inc Placement and Range Guidelines Technical SupportFCC Statement FCC Requirements for Operation in the United StatesIndustry Canada Compliance Statement Bestätigung des Herstellers/Importeurs Certificate of the Manufacturer/Importer Contents Chapter Management Appendix B Related Documents Index Page About This Manual Audience, Scope, Conventions, and FormatsHow to Use This Manual How to Print this ManualRevision History Page Chapter Introduction About the Netgear WG602v4 54 Mbps Wireless Access PointSupport for Standards Key Features Access Point ModeAutosensing Ethernet Connections with Auto Uplink 802.11b/g Standards-based Wireless NetworkingWireless Multimedia WMM Support Compatible and Related Netgear ProductsWhat’s In the Box? Hardware DescriptionWG602v4 Wireless Access Point Front Panel Front Panel LED DescriptionWG602v4 Wireless Access Point Rear Panel Chapter Installation and Configuration Placement and Range GuidelinesBasic Setup and Installation System RequirementsInstalling the WG602v4 Selecting Basic IP Settings OptionsV1.0, June V1.0, June V1.0, June V1.0, June Verifying Wireless Connectivity Deploying the Wireless APIP Address Login Logging Into the WG602v4NetBIOS Name Login NETGEAR123456 Wireless Security Options Range Up to 300 Foot RadiusConfiguring Wireless Security WEP Security Encryption Key Wireless Settings Information Form If WPA-PSK or WPA2-PSK Authentication is UsedConfiguring WEP Wireless Security Configuring WPA-PSK Wireless Security Configuring WPA2-PSK Wireless Security Configuring WPA-PSK/WPA2-PSK Wireless SecurityRestricting Wireless Access by MAC Address V1.0, June V1.0, June V1.0, June Chapter Management Viewing General InformationViewing a List of Attached Devices General Information FieldsUpgrading the Wireless Access Point Software To view the Station ListRebooting and Resetting Factory Defaults Rebooting the Wireless AP Restoring Factory Default SettingsChanging the Administrator Password Configuring Access Point Modes Chapter Advanced ConfigurationConfiguring a WG602v4 as a Point-to-Point Bridge Advanced Configuration AP1 AP2 SegmentConfiguring Wireless Multi-Point Bridging V1.0, June AP2 AP3 Configuring Repeater with Wireless Client Association Click Apply to save your changes Wireless PC Associated with AP1 Client Mode Configuration Check the Client Mode radio boxV1.0, June V1.0, June Site Survey Fields Field DescriptionAdvanced Wireless Settings WG602v4 AP Mode WG602v4 inInternet Client ModeMake any changes and click Apply to save your settings V1.0, June No lights are lit on the access point Chapter TroubleshootingTroubleshooting Ethernet LAN light is not litWireless LAN activity light is not lit Cannot configure the wireless access point from a browserUsing the Reset Button to Restore Factory Default Settings When I enter a URL or IP address I get a timeout errorV1.0, June Default Configuration Settings Table A-1. Access Point Default Configuration SettingsTechnical Specifications Table A-2. Technical SpecificationsVcci V1.0, June Appendix B Related Documents Document LinkV1.0, June Index NumericsIndex-2 Index-3 Index-4

Related manuals

Manual 2 pages 27.86 Kb