APC 6000 Main status bits of system operations, Normal operation Load on battery Disconnected

Page 25

Parallel connected UPS (continued)

Main status bits of system operations

Normal

: inverter powers load and maximum

bit 4C4 = 1

 

 

backup time available

 

Danger

: inverter does not power load

bit 4C6 = 1

Downgraded

:

malfunction or environment fault

bit 4C5 = 1

Load on battery

:

load on battery power

bit 4C7 = 1

Operating modes

The following section describes the different states of a

MGETM GalaxyTM 6000 UPS and the addresses of the bits in the system data array.

Normal operation

Load on battery

Disconnected

Normal:

bit 4C4 = 1

Danger:

bit 4C6 = 0

Downgraded:

bit 4C5 = malfunction dependent

Load on battery:

bit 4C7 = 0

Q1 closed:

bit 40E = 1

Rectifier/charger on:

bit 408 = 1

QF1 closed:

bit 400 = 1

Inverter connected:

bit 484 = 1

Q5N closed:

bit 498 = 1

Normal:

bit 4C4 = 1

Danger:

bit 4C6 = 0

Downgraded:

bit 4C5 = malfunction dependent

Load on battery:

bit 4C7 = 1

Q1 indifferent:

bit 40E = X (N/A)

Rectifier/charger off:

bit 408 = 0

QF1 closed:

bit 400 = 1

Inverter connected:

bit 484 = 1

Q5N closed:

bit 498 = 1

Normal:

bit 4C4 = 0

Danger:

bit 4C6 = 1

Downgraded:

bit 4C5 = X (N/A)

Load on battery:

bit 4C7 = X (N/A)

Q1 indifferent:

bit 40E = X (N/A)

Rectifier/charger indifferent:

bit 408 = X (N/A)

QF1 indifferent:

bit 400 = X (N/A)

Inverter not connected:

bit 484 = X (N/A)

Q5N open:

bit 498 = 0

6739389EN/FB - Page 25

Image 25
Contents GTC link communication interface Mgetm GalaxyTM2 6739389EN/FB Contents Introduction PresentationACQ module COM moduleInterface Communication settingsJbus protocol Synchronizing data exchanges PrincipleDescription of request and response frames Checking received messages on the slave side Function 1 and 2 read N bits FunctionsFunction 5 writing a bit Function 3 and 4 read N wordsFunction 6 writing a word Function 8 reading error diagnosis countersFunction 15 writing n consecutive bits Function 11 reading event countersMSB LSB MSB LSB MSB Function 16 writing n consecutive wordsCRC 16 algorithm Example of CRC computation Table of Most Significant Bytes for CRC16 Computation Example of CRC 16 computation in C using table lookupJbus protocol Unitary UPS UPS theory of operationOperation without battery Parallel connected UPS with Static Switch cubicleUPS without Mains Operation with battery Unitary UPS Block diagramMeasured quantities Main status bits UPS operating information Normal operation Load on batteryOperating modes Load on Mains Load on bypass Parallel connected UPS Main status bits of system operations Normal operation Load on battery DisconnectedStatic Switch cubicle Main indicators of system operations Static SwitchNormal operation Load on Mains Load on bypass Sample commands List of variable fields Example of read data array commands sent by the terminalSystem information Message formatTables of measured data General definitions Signaling fieldCurrent fields Voltage fields Power fields Frequency fieldsTables of binary data Battery and adjustments fieldsRectifier-charger Connectivity InverterGlobal information Table of control devicesWord address Glossary of information descriptorsInverter stack overload 0=no/1=overload Word address 4C Word address 4AWord address 4E summary Word address 4DWord address C1 C10 call reset 0= not activated / 1=activated
Related manuals
Manual 46 pages 29.39 Kb