Anritsu MA24106A, 0701012 manual Time, X-axis 30 minutes

Page 25

Using the Power Sensor

Menu Bar

Clicking Start in the Power Graph menu opens the power versus time graph (Figure 3-12).

Figure 3-12.Power Graph Screen

The default settings of the graph are as follows:

•Time, X-axis: 30 minutes

•Power, Y-axis:+20 dBm to –60 dBm

Clicking Setup opens the Graph Setup dialog (below) where the scales of time and power axes can be changed. Power is in dBm and time is in minutes.

Figure 3-13.PowerGraph Setup Dialog

MA24106A UG

3-7

Image 25

Contents True-RMS, 50 MHz to 6 GHz MA24106A USB Power Sensor User GuideUpdates Anritsu Company Software License Agreement Page Table of Contents Table of Contents General Information Preparation for Storage/Shipment Preparation for Storage/ShipmentDriver Installation InstallationHardware and Software Requirements Anritsu Power Meter Installation Driver InstallationLicense Agreement Installation Driver InstallationSoftware will then install to the selected location Found New Hardware Wizard Select the hardware type Computer, and then click Next Click Have Disk..., and then click Next 14.Found New Hardware Wizard Click Finish to close the wizard Page Graphical User Interface Using the Power SensorButtons Buttons Using the Power SensorData Entry Fields Display Window Using the Power Sensor Display WindowStatus Bar Menu Bar Menu Bar Using the Power SensorFile Menu Tools MenuDataLogging Menu Data Logging Menu10. Data Logging Power GraphTime, X-axis 30 minutes 14.Offset Entry Screen Offset Table16. Open Dialog MA24106A UG 17.Offset Table Menu Offset Table Off Status Session RestoreConnecting the DUT Basic Power MeasurementUsing the Power Sensor Making Measurements Making MeasurementsZeroing the Sensor Making Measurements Using the Power SensorCalibrating the Sensor Applying a Calibration Factor Correction±0.20 dB ±0.15 dB ±0.10 dB ±0.05 dB ±0.01 dB DBm Noise Number Averages Needed forTime Varying Signals Error StatesMeasurement Considerations Using the Power Sensor Message Description ResolutionMultitone Signals High Crest Factor Signals peak to average ratioUsing the Power Sensor Measurement Considerations Noise and AveragingSettling Time Uncertainty of a Measurement Using the Power Sensor Uncertainty of a MeasurementUncertainty Adjusted Specification Uncertainty of a Measurement Using the Power SensorUncertainty Example Noise Calculations at 12 dBm 16 mWCommand Description Remote Operation Commands SummaryRemote Operation Remote Operation Command Details Remote Operation Command DetailsFREQ? Remote Operation Remote Operation Command DetailsHAT Required Equipment Sensor Operational TestsVswr Pretest Test ProcedureVswr Pretest Sensor Operational Tests Sensor Operational Tests Calibration Factor Test Calibration Factor TestMA24106A Calibration Factor Test Sensor Operational TestsSensor Operational Tests Linearity Test Linearity TestApply Linearity Test Sensor Operational TestsSensor Operational Tests Linearity Test +20 +15 +10 Adjust per Max Min Delta E11 E12 Measurement Results 2 GHz Measurement Results 6 GHz Beware of destructive pin depth mating connectors Appendix a Connector Care and HandlingAvoid applying excessive power Avoid over torquing connectorsCleaning connectors Connector Care and HandlingAppendix B Sample Visual Basic Code Using the Demo ApplicationDemo Application Using the Demo Application Sample Visual Basic Code Sample Visual Basic Code Using the Demo Application Delay routine Appendix C Serial Port Compatibility For Anritsu Power Meter 1.0 OnlyMethod 3-Remapping a Serial Port Method 1-Download Updated SoftwareFigure C-2.System Properties Serial Port CompatibilityFigure C-3.Device Manager Method 3-Remapping a Serial PortFigure C-4.Advanced Settings for COM Port Close all windows that you have opened up to this point Upgrading the Firmware Appendix D Upgrading the FirmwareUpgrading the Firmware Figure D-3.Firmware Upgrade DialogFigure D-5.Open File Dialog Figure D-7 Symbols to L SymbolsIndex Index-2 MA24106A UG To SUSB To Z