3Com 980-000077/002 manual Configuring the Remote Unit, Assign the Unit Name

Page 35

Configuring a Remote Unit from the Central Site

3-13

Configuring the Remote Unit

Assign the Unit Name

1Enter CO SYS to display the System Parameters screen.

2Type in the name assigned to the unit in the Unit Name field. The name must be exactly the same as that used to configure the central site unit ISDN Numbers table.

Unit names are case-sensitive and must be entered correctly.

3Press [Ctrl]+[E] to submit the new setting and then enter SAVE

Configure the Ethernet Port

Changing the IP address during the remote management session causes the session to be disconnected when the new IP address is submitted. This is normal.

1Enter CO PO to display the Port Configuration screen.

2Select the LAN1 port using the Arrow keys and enter ED to display the Edit Ethernet Port screen.

3Type the IP address assigned to the unit in the Port IP Address field. The IP address must be exactly the same as that used to configure the central site unit ISDN Autocall table.

4Type a valid subnet mask for the network in the Port IP Mask field.

5Type a number between 6 and 10 in the Port Hop Count field. Increasing this setting from the default may help to prevent routing problems, in some cases.

6Press [Ctrl]+[E] to submit the new setting.

Submitting the IP address causes the remote management session to disconnect immediately.

7Press [Ctrl]+[D] to return to the central site unit management screens.

8Enter REM to display the Remote Units screen and press [Ctrl]+[V] to refresh the screen.

9Select the entry for the remote unit using the Arrow keys. Note that the entry now contains the remote unit name and IP address.

Image 35

Contents Getting Connected Guide 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Contents Index Finding Specific Information in this Guide About this GuideList conventions that are used throughout this guide ConventionsUnit Naming Convention Management System CommandsIntroduction RequirementsLeased Lines One-to-one ConfigurationConfiguration by Telephone Bridging and IP Configuration OptionsBridging and IP Outline of Configuration Procedure Do you wish to keep IP Addresses and Isdn parameters Assign the Unit Name Configure the Ethernet PortConfigure the Isdn Network Type Configure the Isdn Numbers TableConfigure the Isdn IP Autocall Table Configuring a Remote Unit for Bridging and IPConnect to an IP Network Configuring a Unit using the Quick Configuration UtilityAssign the Unit Name, IP Address and Subnet Mask Test the Isdn Numbers and IP Autocall Tables Prior to Despatch Configuring a Remote Unit from the Central SiteConfigure the Isdn Autocall Table on the Central Site Unit Configuring the Central Site UnitConfigure the Isdn Numbers Table on the Central Site Unit Establish a Remote Management Session Configuring the Remote Site UnitConfigure the Ethernet Port Close the Remote Management Session Configure the Isdn Autocall TableCancel the Manual Call Cancelling Isdn Calls 14CHAPTER 2 Bridging and IP Routing IP Routing IP2CHAPTER 3 Routing IP Manual Configuration of a Central Site Unit for Routing IP 4CHAPTER 3 Routing IP Unnumbered links make the best use of available IP addresses Enable IP Routing Configuring a Remote Unit to Route IPConfigure IP Routing-Static Route Entries Configuring a Remote Unit to Route IP Test the IP Autocall and Isdn Numbers Tables Test the Isdn LineLondon Disable Routing on the Central Site Unit Configure the Isdn Numbers Table on the Central Site Unit 12CHAPTER 3 Routing IP Configuring the Remote Unit 14CHAPTER 3 Routing IP Enable Routing on the Remote Unit Configure IP Routing-Static Return Route EntrySave the Remote Unit Configuration Enable Routing on the Central Site UnitCancelling Calls 18CHAPTER 3 Routing IP Novell IPX Bridging Novell IPX and Bridging2CHAPTER 4 Novell IPX and Bridging Do you wish to keep IP Addresses and Isdn parameters 4CHAPTER 4 Novell IPX and Bridging Configuring a Remote Unit for Bridging and IPX Connect to a Novell Network Test the IPX Autocall Table 8CHAPTER 4 Novell IPX and Bridging Configure the Isdn Numbers Table on the Central Site Unit 10CHAPTER 4 Novell IPX and Bridging Build the IPX Autocall Table Enable NRIP/SAP LearningNearest Server Disable NRIP/SAP LearningClose the Remote Management Session 14CHAPTER 4 Novell IPX and Bridging Novell IPX Routing Novell IPX RoutingConfiguring a Central Site Unit for Routing IPX Configuring a Central Site Unit for Routing IPX 4CHAPTER 5 Novell IPX Routing Enable Novell RIP/SAP Learning Enable IPX RoutingConfiguring a Remote Unit to Route IPX Configuring a Remote Unit to Route IPX Specific Server for Get Nearest Server Responses Manual CallNo Specific Server for GNS Responses 10CHAPTER 5 Novell IPX Routing Configure the Isdn Numbers Table on the Central Site Unit 12CHAPTER 5 Novell IPX Routing Configure the Isdn Numbers Table Submitting the new setting turns IPX routing on Enter REM to display the Remote Units screen 16CHAPTER 5 Novell IPX Routing PPP Configuration for IP 6 Connections Configuring a PPP Connection Internet 4CHAPTER 6 PPP Configuration for IP Connections Index Index 10,3-12 Index