3Com 980-000077/002 manual Configuring a Central Site Unit for Routing IPX

Page 57

Configuring a Central Site Unit for Routing IPX

5-3

configuration settings and port type and put it in a safe, accessible place.

If the central site unit is being configured for the first time, or if it is an entirely new installation, then reset the unit to the factory default settings.

1Press the [Return] key.

2Enter PASSWORD (in upper-case letters) when the Enter Password screen is displayed.

3Enter CO STD

4Do you wish to keep IP Addresses and ISDN parameters.

KEEP (Y/N)? is displayed at the command line. Enter N

5This will ERASE all configurations. ERASE (Y/N) is displayed. Enter Y

6System will now reboot is displayed.

7Follow the on-screen instructions.

8Enter PASSWORD when the Enter Password screen is displayed.

9Enter SAVE and then enter QUIT

10Power-cycle the unit by removing and then refitting the power lead.

11Follow the on-screen instructions.

12Enter PASSWORD when the Enter Password screen is displayed.

Following the above sequence will ensure that the unit is reset to the factory default configuration and that the unit database is empty.

Assign the Unit Name

The unit must be assigned a unique name. The unit software relies on associating unit names with ISDN numbers for its core functionality.

1Enter CO SYS to display the System Parameters screen.

2Type a unique name for the unit in the Unit Name field. It can have up to 12 characters but note that the name is case-sensitive. Do not include spaces in the unit name.

3Press [Ctrl]+[E] to submit the new setting and then enter SAVE

Image 57
Contents Getting Connected Guide 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Contents Index Finding Specific Information in this Guide About this GuideList conventions that are used throughout this guide ConventionsIntroduction Management System CommandsRequirements Unit Naming ConventionOne-to-one Configuration Configuration by TelephoneLeased Lines Configuration Options Bridging and IPBridging and IP Outline of Configuration Procedure Do you wish to keep IP Addresses and Isdn parameters Configure the Isdn Network Type Configure the Ethernet PortConfigure the Isdn Numbers Table Assign the Unit NameConfigure the Isdn IP Autocall Table Configuring a Remote Unit for Bridging and IPConfiguring a Unit using the Quick Configuration Utility Assign the Unit Name, IP Address and Subnet MaskConnect to an IP Network Test the Isdn Numbers and IP Autocall Tables Prior to Despatch Configuring a Remote Unit from the Central SiteConfiguring the Central Site Unit Configure the Isdn Numbers Table on the Central Site UnitConfigure the Isdn Autocall Table on the Central Site Unit Establish a Remote Management Session Configuring the Remote Site UnitConfigure the Ethernet Port Configure the Isdn Autocall Table Cancel the Manual CallClose the Remote Management Session Cancelling Isdn Calls 14CHAPTER 2 Bridging and IP Routing IP Routing IP2CHAPTER 3 Routing IP Manual Configuration of a Central Site Unit for Routing IP 4CHAPTER 3 Routing IP Unnumbered links make the best use of available IP addresses Configuring a Remote Unit to Route IP Configure IP Routing-Static Route EntriesEnable IP Routing Configuring a Remote Unit to Route IP Test the IP Autocall and Isdn Numbers Tables Test the Isdn LineLondon Disable Routing on the Central Site Unit Configure the Isdn Numbers Table on the Central Site Unit 12CHAPTER 3 Routing IP Configuring the Remote Unit 14CHAPTER 3 Routing IP Enable Routing on the Remote Unit Configure IP Routing-Static Return Route EntrySave the Remote Unit Configuration Enable Routing on the Central Site UnitCancelling Calls 18CHAPTER 3 Routing IP Novell IPX Bridging Novell IPX and Bridging2CHAPTER 4 Novell IPX and Bridging Do you wish to keep IP Addresses and Isdn parameters 4CHAPTER 4 Novell IPX and Bridging Configuring a Remote Unit for Bridging and IPX Connect to a Novell Network Test the IPX Autocall Table 8CHAPTER 4 Novell IPX and Bridging Configure the Isdn Numbers Table on the Central Site Unit 10CHAPTER 4 Novell IPX and Bridging Build the IPX Autocall Table Enable NRIP/SAP LearningNearest Server Disable NRIP/SAP LearningClose the Remote Management Session 14CHAPTER 4 Novell IPX and Bridging Novell IPX Routing Novell IPX RoutingConfiguring a Central Site Unit for Routing IPX Configuring a Central Site Unit for Routing IPX 4CHAPTER 5 Novell IPX Routing Enable Novell RIP/SAP Learning Enable IPX RoutingConfiguring a Remote Unit to Route IPX Configuring a Remote Unit to Route IPX Specific Server for Get Nearest Server Responses Manual CallNo Specific Server for GNS Responses 10CHAPTER 5 Novell IPX Routing Configure the Isdn Numbers Table on the Central Site Unit 12CHAPTER 5 Novell IPX Routing Configure the Isdn Numbers Table Submitting the new setting turns IPX routing on Enter REM to display the Remote Units screen 16CHAPTER 5 Novell IPX Routing PPP Configuration for IP 6 Connections Configuring a PPP Connection Internet 4CHAPTER 6 PPP Configuration for IP Connections Index Index 10,3-12 Index