3Com 980-000077/002 manual 10CHAPTER 4 Novell IPX and Bridging

Page 50

4-10CHAPTER 4: NOVELL IPX AND BRIDGING

Configuring the Remote Unit

Assign the Unit Name

1Enter CO SYS to display the System Parameters screen.

2Type the name assigned to the unit in the Unit Name field. The name must be exactly the same as that used to configure the central site unit ISDN Numbers table.

Unit names are case-sensitive and must be entered correctly.

3Press [Ctrl]+[E] to submit the new setting and then enter SAVE

Configure the Ethernet Port

A unique port IP address and the network subnet mask are required for the Ethernet port (for management of the unit, even if the network is always entirely connected within a non-IP Netware environment).

Changing the IP address during the remote management session causes the session to be disconnected when the new IP address is submitted. This is normal.

1Enter CO PO to display the Port Configuration screen.

2Select the LAN1 port using the Arrow keys and enter ED to display the Edit Ethernet Port screen.

3Type a valid, unique IP address for the unit in the Port IP Address field. Do not type the network IP address.

4Type a valid subnet mask for the network in the Port IP Mask field.

5Type the IPX network number in the Port IPX Network field. This must be the same number as the central site LAN or LAN segment, or IPX and bridging will not work.

6Use the Spacebar to toggle the setting of the IPX Frame Type field to the correct frame type for the network.

The frame type must be correct for the network environment in which the unit is operating. If the frame type is not correct, the unit will not pass data. Contact the network administrator for more information about the frame type used.

Image 50
Contents Getting Connected Guide 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Contents Index About this Guide Finding Specific Information in this GuideConventions List conventions that are used throughout this guideRequirements Management System CommandsIntroduction Unit Naming ConventionLeased Lines One-to-one ConfigurationConfiguration by Telephone Bridging and IP Configuration OptionsBridging and IP Outline of Configuration Procedure Do you wish to keep IP Addresses and Isdn parameters Configure the Isdn Numbers Table Configure the Ethernet PortConfigure the Isdn Network Type Assign the Unit NameConfiguring a Remote Unit for Bridging and IP Configure the Isdn IP Autocall TableConnect to an IP Network Configuring a Unit using the Quick Configuration UtilityAssign the Unit Name, IP Address and Subnet Mask Test the Isdn Numbers and IP Autocall Tables Configuring a Remote Unit from the Central Site Prior to DespatchConfigure the Isdn Autocall Table on the Central Site Unit Configuring the Central Site UnitConfigure the Isdn Numbers Table on the Central Site Unit Configuring the Remote Site Unit Establish a Remote Management SessionConfigure the Ethernet Port Close the Remote Management Session Configure the Isdn Autocall TableCancel the Manual Call Cancelling Isdn Calls 14CHAPTER 2 Bridging and IP Routing IP Routing IP2CHAPTER 3 Routing IP Manual Configuration of a Central Site Unit for Routing IP 4CHAPTER 3 Routing IP Unnumbered links make the best use of available IP addresses Enable IP Routing Configuring a Remote Unit to Route IPConfigure IP Routing-Static Route Entries Configuring a Remote Unit to Route IP Test the Isdn Line Test the IP Autocall and Isdn Numbers TablesLondon Disable Routing on the Central Site Unit Configure the Isdn Numbers Table on the Central Site Unit 12CHAPTER 3 Routing IP Configuring the Remote Unit 14CHAPTER 3 Routing IP Configure IP Routing-Static Return Route Entry Enable Routing on the Remote UnitEnable Routing on the Central Site Unit Save the Remote Unit ConfigurationCancelling Calls 18CHAPTER 3 Routing IP Novell IPX and Bridging Novell IPX Bridging2CHAPTER 4 Novell IPX and Bridging Do you wish to keep IP Addresses and Isdn parameters 4CHAPTER 4 Novell IPX and Bridging Configuring a Remote Unit for Bridging and IPX Connect to a Novell Network Test the IPX Autocall Table 8CHAPTER 4 Novell IPX and Bridging Configure the Isdn Numbers Table on the Central Site Unit 10CHAPTER 4 Novell IPX and Bridging Enable NRIP/SAP Learning Build the IPX Autocall TableDisable NRIP/SAP Learning Nearest ServerClose the Remote Management Session 14CHAPTER 4 Novell IPX and Bridging Novell IPX Routing Novell IPX RoutingConfiguring a Central Site Unit for Routing IPX Configuring a Central Site Unit for Routing IPX 4CHAPTER 5 Novell IPX Routing Enable IPX Routing Enable Novell RIP/SAP LearningConfiguring a Remote Unit to Route IPX Configuring a Remote Unit to Route IPX Manual Call Specific Server for Get Nearest Server ResponsesNo Specific Server for GNS Responses 10CHAPTER 5 Novell IPX Routing Configure the Isdn Numbers Table on the Central Site Unit 12CHAPTER 5 Novell IPX Routing Configure the Isdn Numbers Table Submitting the new setting turns IPX routing on Enter REM to display the Remote Units screen 16CHAPTER 5 Novell IPX Routing PPP Configuration for IP 6 Connections Configuring a PPP Connection Internet 4CHAPTER 6 PPP Configuration for IP Connections Index Index 10,3-12 Index