Metrologic Instruments MS9500 manual Scanner and Accessories, ∙ Installation and User’s Guide Mlpn

Page 7

Scanner and Accessories

The following list of parts may or may not be included in the MS9500 kit.

∙Voyager MS9520 Single-Line Laser Scanner, or

Voyager MS9540 – CodeGate™ Single-Line Laser Scanner

∙AC to DC Power Transformer – Regulated 5.2VDC @ 650 mA output . One of the following may be included:

120 V United States: MLPN 45-45593

220 V – 240 V Continental European: MLPN 45-45591

220 V – 240 V United Kingdom: MLPN 45-45592

∙PowerLink Cable with built in power jack. One of the following may be included:

Standard: MLPN 53xxx* - 2.7 m (9’) coiled cord, long strain relief

or

Optional: MLPN 54xxx* - 2.1 m (7’) straight cord, short strain relief

*xxx specifies connection to host

∙Stand with mounting accessories

Clip-in Stand: MLPN 46-46055, or

Mask Stand: MLPN 46-46128

∙Installation and User’s Guide – MLPN 2410

Available on Metrologic website – www.metrologic.com

∙MetroSelect Scanner Configuration Guide – MLPN 2407 Available on Metrologic website – www.metrologic.com

Other items may be ordered for the specific protocol being used. To order additional items, contact the dealer, distributor or call Metrologic’s Customer Service Department at 1-800-ID-METRO or 1-800-436-3876.

Caution:

To maintain compliance with applicable standards, all circuits connected to the scanner must meet the requirements for SELV (Safety Extra Low Voltage) according to EN 60950.

To maintain compliance with standard CSA C22.2 No. 950/UL 1950 and norm EN 60950, the power source should meet applicable performance requirements for a limited power source.

2

Image 7

Contents Page USA Corporate Headquarters Europe LocationsIii Table of Contents Appendix D Appendix aAppendix B Appendix CVoyager Voyager CodeGate Interface Introduction∙ Installation and User’s Guide Mlpn Scanner and AccessoriesVoyager MS9540 CodeGate Single-Line Laser Scanner Quick Start Installing the Scanner to the Host System Disconnecting PowerLink Cables from the Scanner Two Modes of Operation How to Use CodeGate MS9540 OnlyKit #46-46055 Contains Assembling the StandStand Option 1 Self-supported Stand Option 2 Hard-mounted to countertop Scanner Parts Razzberry Tone Audible IndicatorsThree Beeps On Power Up One BeepThis is a failure indicator. Refer to Failure Modes on Visual Indicators Steady Red, Green off Alternating Flashing of Green and RedFlashing Green and one Razzberry Tone Failure ModesHow does Serial Programming work? Programming ModesHost Scanner Feature Command Ascii Representation Response Abbreviated Ascii Table Upgrading the Flash Rom Firmware Avoid Exposure laser light emitted from this aperture LabelsWidth of Scan Field Depth of FieldDistance Scanner FaceIR Activation Maintenance Scanner Version Communication Protocols Identifier Applications and ProtocolsTrouble Shooting Guide Symptoms Possible Causes Solution Troubleshooting GuideTroubleshooting Guide Unit scans Receiving data but RS-232 Demonstration Program Operational Appendix a Design SpecificationsLight IBM KBW PEN Appendix B Default SettingsDTS/SIEMENS DTS/NIXDORF NCR F NCR S 46XX Light IBM Parameter Msec to Find Supplement Programmable Msec steps max Rdata Appendix CPin D-type female connector to the PC Function Cable Connector Configurations Standard PowerLink cableAdapter Cable Pin Male DIN Pin Function Cable Connector ConfigurationPowerLink Cable Pin Female DIN Pin Function Pin Male Mini-DIN Pin FunctionLimited Warranty Appendix D Warranty and DisclaimerRemarque Appendix E NoticesAttenzione AchtungPatents Appendix FAddendum AddendumCdrh IndexRMA