Datalogic Scanning PDA user manual RF Connection, Enabling Terminals for RF Connectivity

Page 64

Terminal to FMU Server Communications

RF Connection

For RF units, terminal(s) need to have existing communication to a wireless network. See the PRG for your terminal for complete information.

Enabling Terminals for RF Connectivity

Each terminal that you want to connect to FMU must be enabled for FMU. This only needs to be done once for each terminal upon initial installation.

To enable a terminal for FMU:

1.On the terminal you want to set up:

WinCE:

Go to Start > Programs > Falcon Management > FMUinit.

Windows Mobile:

Tap > Settings > System > Falcon Config.

2.Select Enable FMU Client.

3.Select Network for the Connection field.

4.Choose the Discovery method by selecting Manual or DHCP in the

Discovery field.

Select Manual to specify the FMU Server manually (see Figure 24A).

Select DHCP to allow the FMU Server settings to be obtained automatically using DHCP Discovery (see Figure 24B). Refer to Appendix B on page 61 for information on configuring your network to support DHCP Discovery.

5.Enter the server name or IP address in the IP Address field.

52

Falcon® Management Utility (FMU)

Image 64
Contents User’s Manual Disclaimer Datalogic Mobile, IncPatents Table of Contents Printing Reports Terminal Properties Appendix D. Glossary Definitions Payment and Taxes Infringement General Provisions Preface OverviewRegistration Style Conventions Manual Formatting ConventionsQuick Start Introduction AdvantagesFeatures System Requirements Supported portablesSystem Requirements Complete System/Workstation MinimumInstalling FMU FMU Installation OptionsBefore You Begin Establish Communication to TerminalsSetting Up File Sharing Using FirewallsFirewalls and File Sharing \Program Files\Datalogic\FMU\Workstation\Pack- ages Complete System Setting Up FMUSeparate Workstation/Server Single Server Support FMU Server ArchitectureFMU Console Terminals Single Server Multiple Server Support Terminal GroupsChapter About FMU FMU’s TechnologyFMU Server and Client User Interface Maintaining Current FilesMost features of FMU can be accessed several different ways Menu Toolbar Start Shortcut Tree View List ViewFMU Components FMU StartConfiguration Configuration Assigned Pa TerminalServers GroupsAssigned Packages Available PackagesTerminal File MenuAdd Assign Packages Update Terminals NowExit Edit View Help Toolbar Printing ReportsAbout FMU Chapter FMU Operation Managing ServersName Adding a ServerIP Address Server Path Deleting a Server Server Error LogViewing or Editing Server Properties Allow older UpdatesAdd License Working with Groups Group Configuration SettingsAdding a Group Deleting a Group Adding and Assigning Packages Renaming a GroupAdding a Package Adding Files to a PackageSource DestinationKeyboard RF CardAdding a Firmware Image File Terminal typeImage FirmwareViewing a File List BoardAssigning a Package TerminalsTerminal Setup Adding TerminalsTerminal Check-in IP AddressDelete Terminal Terminal PropertiesFile Properties Working with FilesAbout Files FMU Operation Configuration Settings Configuration SettingsAll Off Reset ValuesAll On Symbology Settings Configure Symbology SettingsDevice Settings Configure Device SettingsNetwork Settings Description Action Enable DhcpSubnet Mask GatewayFDU Configuration Settings 2D Imager Settings Imager Configuration SettingsConfiguration Settings Terminal to FMU Server Communications Direct Connect Enabling a Terminal for FMU with Direct ConnectWinCE Windows MobileUpdate Time Explore TerminalUpdating Terminals Have an RF connection. See RF Connection onRF Connection Enabling Terminals for RF ConnectivityFor the update to run Select Manual or DhcpClick OK to complete the setup Exploring an RF Terminal Updating RF TerminalsTerminal Configuration Settings Scheduled Update TimeTerminal Configuration Terminal Report Snmp Concepts MIB FilesAdditional Resources Datalogic MIBsAppendix B Dhcp Server Setup Setting up your Dhcp ServerDhcp Server Setup Appendix C Troubleshooting RF Connectivity StartWindows Firewall Issues How to Open Ports in the Windows FirewallUsed by Ports FMUFast FMUTrapshotTroubleshooting Click Add Port Troubleshooting Network Domain File Transfer Troubleshooting Troubleshooting User’s Manual Windows XP Home Installing the Server Only component using XP HomeCreating a Share in Windows XP Home Windows XP Home Reseller Technical Support Technical SupportTelephone Technical Support Sample Reports Terminal Report F00000001Troubleshooting 1D Bar Code 2D Bar CodeActiveSync Check DigitFalcon Config DevicePartnership Falcon Management Utility FMUServer Error Log Network IDPackages Portable DataSymbology Start Subnet MaskTracert Locator URLNET Add Architecture Basic Files Complete SystemControl Datalogic MIBs Falcon Management UtilityMIB MIB Files Network Network Settings Package KeystrokesMenubar PrintingTroubleshooting Uniform Resource Locator URLUSB User Interface XMLIndex User’s Manual Index Ascii Character Set Corporate Headquarters