Yamaha LPX-510 owner manual Replacing the Lamp

Page 56

Maintenance

•The lamp replacement warning message is set to appear after approximately 1600 hours

of lamp use in order to maintain the brightness and quality of the projected images. The time taken for the message to be displayed will vary depending on factors such as the lamp power setting and the picture mode setting.

If you continue to use the lamp after this period, the possibility of the lamp breaking becomes greater.

When the lamp replacement message appears, replace the lamp with a new one as soon as possible, even if it is still working.

•The actual life of each individual lamp will vary depending on the characteristics of the lamp and on the way it has been used. The lamp may become dark or be off even before the lamp replacement message appears. You should always have a spare lamp ready in case it is needed.

•Contact your dealer for a spare lamp.

Replacing the Lamp

•If the lamp stops working and needs to be replaced, it could have been broken.

If replacing the lamp of a projector which has been installed to the ceiling, you should remove the projector from the ceiling before replacing the lamp.

•Wait for the lamp to cool down sufficiently before removing the lamp cover. It takes approximately one hour after the cool-down period has finished before the lamp is cool enough to be removed.

1

2

Turn off the power, wait for the cool- down period to finish (takes approximately 30 seconds), then disconnect the power cord.

*Wait until the lamp cools down (takes approximately 1 hour).

Loosen the screws fixing the lamp cover.

3	Remove the lamp cover.
3	Lift the lamp cover up slightly from the bottom to
	remove it.

Appendices

53

Image 56

Contents LPX-510 Important Safety Instructions FCC Information for US customers We Want You Listening For a LifetimeInstallation OperationOthers For U.K. customersAlleen voor klanten in Nederland IndicationsContents Do not touch the lens with bare hands Remove the batteries from the remote control before storageAttach the lens cap to the lens Retract the adjustable foot Accessories Check the included accessoriesFeatures of the Projector Equipped with a wide- angle lens shift functionTurning On the Projector Turning Off the ProjectorConnecting the Power Cord Check that the power is turned off for allTurning On the Projector Components connected toTurning On the Power and Projecting Images Turn on the power for all equipmentConnected to the projector Turning On the ProjectorNEC If not using the projector for long Turning Off the ProjectorProjector Cord plug from the wall outletExtended Attach the lens capDisconnect the cords that are EquipmentAdjusting the Screen Image Adjusting the Image Size Zoom adjustmentAdjust the image size Exit adjustment modeProjection image position adjustment Lens shift Turn the two lens shift dials to adjustCorrecting Keystone Distortion Keystone Select a pattern Confirm the pattern selectionCrosshatch Grayscale patternExit the pattern display Adjust the focus Adjusting the Image QualityFocus adjustment Brightness adjustment Iris adjustment Select a setting valueSelecting the picture mode Select the picture modePress the Aspect button on Button on the remote controlSelect the aspect mode Zoom mode Normal modeSqueeze mode Squeeze Through mode Smart Zoom modeThrough mode Advanced Operations Functions for Enhancing Projection Description of FunctionsAbsolute Color Temperature and Flesh Tone Adjustment RGB adjustmentAdjusting flesh tones Abs. Color TempSaving and Retrieving Image Quality Settings Memory Save Settings that can be saved in memoryStoring image quality settings Menus p.28Retrieving Saved Image Quality Settings Control panel or the button onUsing the Menu Functions List of MenusFull menu Line menuAdvanced Operations Picture Quality Input A, B Component When computer signals are being inputImage Menu Color Adjustment Picture Mode *1Auto Setup *1 ResetSetup Menu SignalScreen Vertical SizeZoom Lock User’s Logo On-Screen DisplayReset Menu Info MenuUsing the Menus Select a setting item in the sub-menuDisplaying and Operating Full Menus Display the menu screenExit the menu display Change the settingDisplaying and Operating Line Menus Select an item to be set Troubleshooting When Having Some TroubleWhen Having Some Trouble GuideWhen Having Some Trouble No images appear When the Indicators Provide No HelpProblems relating to images Images are fuzzy or out of focus Message No Signal. is displayedMessage Not Supported. is displayed Interference or distortion appear in images Image is truncated large or smallImage colors are not right Images appear darkProjection stops automatically Vertical interference appears in the projected imagesProblems when projection starts Power does not turn onProblems with the remote control Remote control does not workGlossary MaintenanceSpecifications Appearance Maintenance Cleaning Cleaning the Projector Case Cleaning the LensCleaning the Air Filter Turn off the power, wait for the coolRemoving the Air Filter Down period to end takesLamp Replacement Period Install the air filterInstall the air filter cover LAMP/COVER indicator flashes orange or lights redReplacing the Lamp Install the new lamp Install the lamp cover, then tightenLoosen the screws fixing the lamp Remove the old lamp Securely tighten the lamp fixing screwsReset the lamp operating time Resetting the Lamp Operating TimeExample While checking the tone adjustment Screen, adjust the settings startingFrom the one where the vertical stripe Portions of the image, adjustOptional Accessories Lamp cartridgeCeiling mount bracket for low ceilings Ceiling mount bracket for high ceilingsList of Supported Signal Resolutions Component Video/RGB VideoAnalog-RGB signals/signals input to the Hdmi port Specifications Center of lens = Default lens shift position AppearancePart Names and Functions LAMP/COVER indicator p.42 Indicator p.6, 7Setting button p.11, 16 TEMP/FAN indicator p.42D4 Video port Setup Guide Input A/INPUT B ports Setup GuideHdmi port Setup Guide Video port Setup GuideIndicator Light switch Setup GuideZoom button p.11 Iris button p.17Glossary ComponentGlossary SyncPage 2004 Before Using the Remote Control Screen Size and Setting-up Distance Setting-up MethodsInserting the batteries and replacement period Battery Replacement PeriodUsing the remote control and remote operating range Screen Size and Setting-up Distance Setting-up Methods Connecting to a home theater system Connecting to a Computer Computer Incorrect CorrectFalsch RichtigIncorrecto Correcto