BenQ MP525 ST, MP515 ST user manual Connecting an S-Video/composite Video source device

Page 22

Connecting an S-Video/composite Video source device

Examine your Video source device to determine if it has an unused S-Video/Video output jack available:

•If it has both jacks, use the S-Video output jack for connection as the S-Video terminal provides better picture quality than the Video terminal.

•If it has either of the output jack, you can also continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to an S-Video/Video source device:

1.Take an S-Video/Video cable and connect one end to the S-Video/Video output jack of the Video source device.

2.Connect the other end of the S-Video/Video cable to the S-VIDEO/VIDEOjack on the projector.

3.If you wish to make use of the projector (mixed mono) speaker(s) in your presentations, take a suitable audio cable and connect one end of the cable to the audio output jack of the device, and the other end to the AUDIO (L/R) jack of the projector.

Once connected, the audio can be controlled by the projector On-Screen Display (OSD) menus. See "Audio Settings" on page 49 for details.

The built-in speaker will be muted when the AUDIO OUT jack is connected.

• The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See "Connecting audio" on page 20 for details.

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

22 Connection

Page 21 Page 23
Image 22
Page 21 Page 23
Contents
Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Safety Instructions Locations near fire alarms Installation Projector features IntroductionShipping contents Front/upper side Projector exterior viewRear/lower side Controls and functions ProjectorMode Selects an available picture setupMode/Enter Activates the selected On-Screen Display OSD menu itemFreeze Remote controlVolume + Digital Zoom +Timer On Up/Down Remote control effective rangeReplacing the remote control battery Timer Set upFront Table Positioning your projectorChoosing a location Front CeilingAspect image in a Aspect display area Select your screen sizePositioning your projector Projection dimensions Inch Connection Connecting a computer Connecting a computer or monitorTo connect the projector to a notebook or desktop computer Connecting Video source devices Connecting audioTo connect the projector to an Hdmi device Connecting a Component Video source deviceConnecting an Hdmi device To connect the projector to a Component Video source deviceConnecting an S-Video/composite Video source device To connect the projector to an S-Video/Video source deviceStarting up the projector OperationBeen applied Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Using the OSD menu Fine-tuning the image size and clarityUsing the remote control Correcting keystonePress / to select a Using the menusUse / to highlight the System Setup Basic menu Preferred languageSetting a password Using a security cable lockUtilizing the password function To the Security SettingsEntering the password recall procedure If you forget the passwordChanging the password Write down the number and turn off your projectorDisabling the password function Changing Color Space Switching input signalColor space Selecting the aspect ratio Magnifying and searching for detailsPress Digital Zoom+/- to display the Zoom bar About the aspect ratio Selecting a picture mode Using Wall ColorOptimizing the image Go to the Picture Picture Mode menu Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Sharpness Adjusting ColorAdjusting Tint Adjusting Brilliant ColorTo adjust the settings To cancel the timer, perform the following steps Setting the presentation timerTo highlight Off and press Mode/Enter How to use the Timer On key? Hiding the imageFreezing the image Utilizing FAQ functionPress Mode/Enter Locking control keys To activate the High Altitude ModeOperating in a high altitude environment Highlight Yes and press Mode/Enter to confirmTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Personalizing the projector menu displayOnce the cooling process finishes, a Power Off Ring Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system BasicAdvanced Informa Description of each menu Timer TemperatureSave Settings ColorAuto Power Off System Setup Basic menuMenu Settings Blank TimerChange Password Lamp ModeLamp Settings Reset Lamp Timer Settings On page 27 for details Power On LockSettings Signal carries closed captionsReset All Returns all settings to the factory preset values FAQ-Image InstallationMaintenance Care of the projectorGetting to know the lamp hour Setting Lamp Mode as EconomicLamp information Extending lamp lifeTiming of replacing the lamp Lamp has been in operation equivalent to HoursReplacing the lamp Page Tighten the screw that secures the lamp Resetting the lamp timerLamp time will be reset to Restart the projectorLamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Ceiling mount installation DimensionsMm W x 114 mm H x 236 mm D Timing chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsCopyright Limited warrantyDisclaimer EEC statement Regulation statementsFCC statement Weee directiveRegulation statements
Related manuals
Manual 66 pages 8.62 Kb
Top Page Image Contents