Informa | BenQ MP515 ST, MP525 ST manual

BenQ MP515 ST, MP525 ST user manual Informa

Page 45

Main menu	Sub-menu		Options
5.		Closed Caption	On/Off
SYSTEM	Closed Caption Enable
SYSTEM		Caption Version	CC1/CC2/CC3/CC4
SETUP:		Caption Version	CC1/CC2/CC3/CC4
SETUP:
Advanced	Reset All Settings
	FAQ-Image and Installation
	FAQ-Features and Service
6.			•	Source
INFORMA-			•	Picture Mode
TION	Current System Status		•	Resolution
TION	Current System Status		•	Color System
			•	Color System
			•	Equivalent Lamp Hour
			•	Firmware Version

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

Operation 45

Image 45

Contents

Welcome Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Safety Instructions Locations near fire alarms Installation Introduction Projector featuresShipping contents Projector exterior view Front/upper sideRear/lower side Projector Controls and functionsMode/Enter Selects an available picture setupMode Activates the selected On-Screen Display OSD menu itemVolume + Remote controlFreeze Digital Zoom +Replacing the remote control battery Remote control effective rangeTimer On Up/Down Timer Set upChoosing a location Positioning your projectorFront Table Front CeilingSelect your screen size Aspect image in a Aspect display areaPositioning your projector Inch Projection dimensionsConnection Connecting a computer or monitor Connecting a computerTo connect the projector to a notebook or desktop computer Connecting audio Connecting Video source devicesConnecting an Hdmi device Connecting a Component Video source deviceTo connect the projector to an Hdmi device To connect the projector to a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite Video source deviceOperation Starting up the projectorBeen applied Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Using the remote control Fine-tuning the image size and clarityUsing the OSD menu Correcting keystoneUse / to highlight the System Setup Basic menu Using the menusPress / to select a Preferred languageUtilizing the password function Using a security cable lockSetting a password To the Security SettingsChanging the password If you forget the passwordEntering the password recall procedure Write down the number and turn off your projectorDisabling the password function Switching input signal Changing Color SpaceColor space Magnifying and searching for details Selecting the aspect ratioPress Digital Zoom+/- to display the Zoom bar About the aspect ratio Using Wall Color Selecting a picture modeOptimizing the image Setting the User 1/User 2 mode Fine-tuning the image quality in user modesGo to the Picture Picture Mode menu Adjusting BrightnessAdjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Brilliant ColorTo adjust the settings Setting the presentation timer To cancel the timer, perform the following stepsTo highlight Off and press Mode/Enter Hiding the image How to use the Timer On key?Utilizing FAQ function Freezing the imagePress Mode/Enter Operating in a high altitude environment To activate the High Altitude ModeLocking control keys Highlight Yes and press Mode/Enter to confirm Adjusting the sound level Adjusting the sound Turning off the Power On/Off Ring Tone Personalizing the projector menu displayShutting down the projector Once the cooling process finishes, a Power Off RingMenu system Menu operationMain menu Sub-menu Options BasicAdvanced Informa Description of each menu Save Settings TemperatureTimer ColorMenu Settings System Setup Basic menuAuto Power Off Blank TimerLamp Settings Reset Lamp Timer Lamp ModeChange Password Settings On page 27 for details Power On LockReset All Returns all settings to the factory preset values Signal carries closed captionsSettings FAQ-Image InstallationCare of the projector MaintenanceLamp information Setting Lamp Mode as EconomicGetting to know the lamp hour Extending lamp lifeLamp has been in operation equivalent to Hours Timing of replacing the lampReplacing the lamp Page Lamp time will be reset to Resetting the lamp timerTighten the screw that secures the lamp Restart the projectorLight Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Specifications Dimensions Ceiling mount installationMm W x 114 mm H x 236 mm D Supported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputLimited warranty CopyrightDisclaimer FCC statement Regulation statementsEEC statement Weee directiveRegulation statements

Related manuals

BenQ MP515 ST, MP525 ST user manual Informa

Main menu

SETUP:

Advanced

INFORMA-

TION