BenQ MP515 ST Timing of replacing the lamp, Lamp has been in operation equivalent to Hours

Page 53

Timing of replacing the lamp

When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode. Go to http://lamp.BenQ.com for a replacement lamp.

The LAMP indicator light and TEMPerature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after turning the power back on, please contact your dealer. See "Indicators" on page 57 for details.

The following Lamp warning displays will remind you to change the lamp.

Status

Message

 

 

The lamp has been in operation equivalent to

Notice

2500 hours. Install a new lamp for optimal

 

performance. If the projector is normally run with

Order Replacement Lamp

Economic selected (see "Getting to know the lamp

 

hour" on page 52), you may continue to operate

Lamp > 2500 Hours

the projector until the 2950 hour lamp warning

Order a new lamp at lamp.benq.com

appears.

 

 

OK

 

 

The lamp has been in operation equivalent to

Notice

2950 hours. A new lamp should be fitted to avoid

 

the inconvenience when the projector runs out of

Replace Lamp Soon

lamp time.

 

 

Lamp > 2950 Hours

 

Order a new lamp at lamp.benq.com

 

OK

 

 

The lamp has been in operation equivalent to

Notice

3000 hours.

Replace Lamp Now

 

It is strongly recommended that you replace the

 

lamp at this age. The lamp is a consumable item.

Lamp > 3000 Hours

The lamp brightness diminishes with use. This is

Lamp usage time exceeded

normal lamp behavior. You can replace the lamp

Order a new lamp at lamp.benq.com

whenever you notice that the brightness level has

OK

significantly diminished. If the lamp is not

 

replaced beforehand, it must be replaced after

 

3000 hours usage.

 

 

 

The lamp MUST be replaced before the projector

Notice

will operate normally.

 

 

Out of Lamp Usage Time

 

Replace lamp (refer to user manual)

 

Then reset lamp timer

 

Order a new lamp at lamp.benq.com

 

OK

 

 

Maintenance 53

Image 53
Contents Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Safety Instructions Locations near fire alarms Installation Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewFront/upper side Projector Controls and functionsMode/Enter Selects an available picture setupMode Activates the selected On-Screen Display OSD menu itemVolume + Remote controlFreeze Digital Zoom +Replacing the remote control battery Remote control effective rangeTimer On Up/Down Timer Set upChoosing a location Positioning your projectorFront Table Front CeilingSelect your screen size Aspect image in a Aspect display areaPositioning your projector Inch Projection dimensionsConnection To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting audio Connecting Video source devicesConnecting an Hdmi device Connecting a Component Video source deviceTo connect the projector to an Hdmi device To connect the projector to a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite Video source deviceBeen applied OperationStarting up the projector Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Using the remote control Fine-tuning the image size and clarityUsing the OSD menu Correcting keystoneUse / to highlight the System Setup Basic menu Using the menusPress / to select a Preferred languageUtilizing the password function Using a security cable lockSetting a password To the Security SettingsChanging the password If you forget the passwordEntering the password recall procedure Write down the number and turn off your projectorDisabling the password function Color space Switching input signalChanging Color Space Press Digital Zoom+/- to display the Zoom bar Magnifying and searching for detailsSelecting the aspect ratio About the aspect ratio Optimizing the image Using Wall ColorSelecting a picture mode Setting the User 1/User 2 mode Fine-tuning the image quality in user modesGo to the Picture Picture Mode menu Adjusting BrightnessAdjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Brilliant ColorTo adjust the settings To highlight Off and press Mode/Enter Setting the presentation timerTo cancel the timer, perform the following steps Hiding the image How to use the Timer On key?Press Mode/Enter Utilizing FAQ functionFreezing the image Operating in a high altitude environment To activate the High Altitude ModeLocking control keys Highlight Yes and press Mode/Enter to confirmAdjusting the sound level Adjusting the soundTurning off the Power On/Off Ring Tone Personalizing the projector menu displayShutting down the projector Once the cooling process finishes, a Power Off RingMenu system Menu operationMain menu Sub-menu Options BasicAdvanced Informa Description of each menu Save Settings TemperatureTimer ColorMenu Settings System Setup Basic menuAuto Power Off Blank TimerLamp Settings Reset Lamp Timer Lamp ModeChange Password Settings On page 27 for details Power On LockReset All Returns all settings to the factory preset values Signal carries closed captionsSettings FAQ-Image InstallationCare of the projector MaintenanceLamp information Setting Lamp Mode as EconomicGetting to know the lamp hour Extending lamp lifeLamp has been in operation equivalent to Hours Timing of replacing the lampReplacing the lamp Page Lamp time will be reset to Resetting the lamp timerTighten the screw that secures the lamp Restart the projectorLight Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Specifications Mm W x 114 mm H x 236 mm D DimensionsCeiling mount installation Supported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputDisclaimer Limited warrantyCopyright FCC statement Regulation statementsEEC statement Weee directiveRegulation statements
Related manuals
Manual 66 pages 8.62 Kb

MP515 ST, MP525 ST specifications

The BenQ MP525 ST and MP515 ST are innovative projectors designed to deliver high-quality visuals for both educational and business environments. With a blend of advanced technologies and user-friendly features, these projectors offer exceptional performance.

Starting with the core characteristics, both models boast DLP (Digital Light Processing) technology, which ensures sharp images with vibrant colors and excellent contrast ratios. The native resolution of these projectors is XGA (1024 x 768), suitable for detailed presentations and videos. The brightness level for the MP525 ST is typically around 2500 ANSI lumens, providing sufficient illumination for well-lit environments. The MP515 ST, while slightly less bright, still delivers adequate performance for dimly lit rooms, making both models versatile for various settings.

One of the standout features of the BenQ MP525 ST is its short-throw projection capability, allowing users to display large images from a short distance. This is particularly beneficial in smaller rooms where space is limited as it minimizes shadows and enables presenters to stay close to their audience. The throw ratio is approximately 0.6:1, meaning it can project a large image within just a few feet from the screen.

Both projectors come equipped with a comprehensive connectivity suite, including HDMI, VGA, S-Video, and composite video inputs, ensuring compatibility with a wide range of devices such as laptops, DVD players, and gaming consoles. They also feature built-in speakers that deliver clear audio without the need for external sound systems, making them convenient for quick setups.

In terms of usability, the BenQ MP525 ST and MP515 ST are designed with user-friendly interfaces and remote controls. They include features like keystone correction to help adjust the image shape, ensuring perfect alignment even when the projector is angled. Additionally, the projector’s lamp life is impressive, reaching up to 4000 hours in economic mode, which reduces the need for frequent replacements and lowers operational costs.

In conclusion, the BenQ MP525 ST and MP515 ST projectors are excellent choices for educators and presenters who require flexibility, quality, and ease of use in their projection equipment. With their advanced DLP technology, short-throw capabilities, and versatile connectivity options, these models cater to diverse presentation needs while ensuring that every image is displayed with clarity and impact.