BenQ MP525 ST, MP515 ST Signal carries closed captions, Closed Caption, Caption Version, Settings

Page 50

5. SYSTEM SETUP: Advanced menu

6. INFORMATION menu

Function

Description

 

Closed Caption Enable

 

Activates the function by selecting On when the selected input

 

signal carries closed captions.

 

• Captions: An on-screen display of the dialogue, narration,

Closed Caption

and sound effects of TV programs and videos that are

 

closed captioned (usually marked as "CC" in TV listings).

 

Caption Version

 

Selects a preferred closed captioning mode. To view captions,

 

select CC1, CC2, CC3, or CC4 (CC1 displays captions in the

 

primary language in your area).

 

 

Reset All

Returns all settings to the factory preset values.

The following settings will still remain: Position, Phase, H. Size,

Settings

User 1, User 2, Color Space Conversion, Language, Projector

 

Position, High Altitude Mode, Security Settings, and Baud Rate.

FAQ-Image and

 

Installation

Displays possible solutions to problems you may encounter.

 

FAQ-Features

 

and Service

 

 

 

 

Source

 

Shows the current signal source.

 

Picture Mode

 

Shows the selected mode in the PICTURE menu.

 

Resolution

Current System

Shows the native resolution of the input signal.

Status

Color System

 

Shows input system format: NTSC, PAL, SECAM, or RGB.

 

Equivalent Lamp Hour

 

Displays the number of hours the lamp has been used.

 

Firmware Version

 

Shows the firmware version of your projector.

 

 

50 Operation

Page 49 Page 51
Image 50
Page 49 Page 51
Contents
Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Safety Instructions Locations near fire alarms Installation Projector features IntroductionShipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions ProjectorMode Selects an available picture setupMode/Enter Activates the selected On-Screen Display OSD menu itemFreeze Remote controlVolume + Digital Zoom +Timer On Up/Down Remote control effective rangeReplacing the remote control battery Timer Set upFront Table Positioning your projectorChoosing a location Front CeilingAspect image in a Aspect display area Select your screen sizePositioning your projector Projection dimensions InchConnection To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting Video source devices Connecting audioTo connect the projector to an Hdmi device Connecting a Component Video source deviceConnecting an Hdmi device To connect the projector to a Component Video source deviceConnecting an S-Video/composite Video source device To connect the projector to an S-Video/Video source deviceBeen applied OperationStarting up the projector Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Using the OSD menu Fine-tuning the image size and clarityUsing the remote control Correcting keystonePress / to select a Using the menusUse / to highlight the System Setup Basic menu Preferred languageSetting a password Using a security cable lockUtilizing the password function To the Security SettingsEntering the password recall procedure If you forget the passwordChanging the password Write down the number and turn off your projectorDisabling the password function Color space Switching input signalChanging Color Space Press Digital Zoom+/- to display the Zoom bar Magnifying and searching for detailsSelecting the aspect ratio About the aspect ratio Optimizing the image Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Sharpness Adjusting ColorAdjusting Tint Adjusting Brilliant ColorTo adjust the settings To highlight Off and press Mode/Enter Setting the presentation timerTo cancel the timer, perform the following steps How to use the Timer On key? Hiding the imagePress Mode/Enter Utilizing FAQ functionFreezing the image Locking control keys To activate the High Altitude ModeOperating in a high altitude environment Highlight Yes and press Mode/Enter to confirmTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Personalizing the projector menu displayOnce the cooling process finishes, a Power Off Ring Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system BasicAdvanced Informa Description of each menu Timer TemperatureSave Settings ColorAuto Power Off System Setup Basic menuMenu Settings Blank TimerChange Password Lamp ModeLamp Settings Reset Lamp Timer Settings On page 27 for details Power On LockSettings Signal carries closed captionsReset All Returns all settings to the factory preset values FAQ-Image InstallationMaintenance Care of the projectorGetting to know the lamp hour Setting Lamp Mode as EconomicLamp information Extending lamp lifeTiming of replacing the lamp Lamp has been in operation equivalent to HoursReplacing the lamp Page Tighten the screw that secures the lamp Resetting the lamp timerLamp time will be reset to Restart the projectorLamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Mm W x 114 mm H x 236 mm D DimensionsCeiling mount installation Timing chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsDisclaimer Limited warrantyCopyright EEC statement Regulation statementsFCC statement Weee directiveRegulation statements
Related manuals
Manual 66 pages 8.62 Kb
Top Page Image Contents