BenQ MP525 ST, MP515 ST user manual Safety Instructions

Page 4

Safety Instructions (Continued)

7.When the auto blank sensor does not work and the projector is under operation, do not block the projection lens with any objects as this could cause the objects to become heated and deformed or even cause a fire. To temporarily turn off the lamp, press BLANK on the projector or remote control.

8.The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.

9.Never replace the lamp assembly or any electronic components unless the projector is unplugged.

10.Do not operate lamps beyond the rated lamp life. Excessive operation of lamps beyond the rated life could cause them to break on rare occasions.

11.Do not place this product on an unstable cart, stand, or table. The product may fall, sustaining serious damage.

12.Do not stand the projector on end vertically. Doing so may cause the projector to fall over, causing injury or resulting in damage to the projector.

4 Important safety instructions

Page 3 Page 5
Image 4
Page 3 Page 5
Contents
Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Safety Instructions Locations near fire alarms Installation Projector features IntroductionShipping contents Front/upper side Projector exterior viewRear/lower side Controls and functions ProjectorSelects an available picture setup Mode/EnterMode Activates the selected On-Screen Display OSD menu itemRemote control Volume +Freeze Digital Zoom +Remote control effective range Replacing the remote control batteryTimer On Up/Down Timer Set upPositioning your projector Choosing a locationFront Table Front CeilingAspect image in a Aspect display area Select your screen sizePositioning your projector Projection dimensions InchConnection Connecting a computer Connecting a computer or monitorTo connect the projector to a notebook or desktop computer Connecting Video source devices Connecting audioConnecting a Component Video source device Connecting an Hdmi deviceTo connect the projector to an Hdmi device To connect the projector to a Component Video source deviceConnecting an S-Video/composite Video source device To connect the projector to an S-Video/Video source deviceStarting up the projector OperationBeen applied Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Using the remote controlUsing the OSD menu Correcting keystoneUsing the menus Use / to highlight the System Setup Basic menuPress / to select a Preferred languageUsing a security cable lock Utilizing the password functionSetting a password To the Security SettingsIf you forget the password Changing the passwordEntering the password recall procedure Write down the number and turn off your projectorDisabling the password function Changing Color Space Switching input signalColor space Selecting the aspect ratio Magnifying and searching for detailsPress Digital Zoom+/- to display the Zoom bar About the aspect ratio Selecting a picture mode Using Wall ColorOptimizing the image Fine-tuning the image quality in user modes Setting the User 1/User 2 modeGo to the Picture Picture Mode menu Adjusting BrightnessAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Brilliant ColorTo adjust the settings To cancel the timer, perform the following steps Setting the presentation timerTo highlight Off and press Mode/Enter How to use the Timer On key? Hiding the imageFreezing the image Utilizing FAQ functionPress Mode/Enter To activate the High Altitude Mode Operating in a high altitude environmentLocking control keys Highlight Yes and press Mode/Enter to confirmAdjusting the sound Adjusting the sound levelTurning off the Power On/Off Ring Tone Personalizing the projector menu displayOnce the cooling process finishes, a Power Off Ring Shutting down the projectorMenu operation Menu systemMain menu Sub-menu Options BasicAdvanced Informa Description of each menu Temperature Save SettingsTimer ColorSystem Setup Basic menu Menu SettingsAuto Power Off Blank TimerLamp Mode Lamp Settings Reset Lamp TimerChange Password Settings On page 27 for details Power On LockSignal carries closed captions Reset All Returns all settings to the factory preset valuesSettings FAQ-Image InstallationMaintenance Care of the projectorSetting Lamp Mode as Economic Lamp informationGetting to know the lamp hour Extending lamp lifeTiming of replacing the lamp Lamp has been in operation equivalent to HoursReplacing the lamp Page Resetting the lamp timer Lamp time will be reset toTighten the screw that secures the lamp Restart the projectorIndicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Ceiling mount installation DimensionsMm W x 114 mm H x 236 mm D Timing chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsCopyright Limited warrantyDisclaimer Regulation statements FCC statementEEC statement Weee directiveRegulation statements
Related manuals
Manual 66 pages 8.62 Kb
Top Page Image Contents