BenQ MP515 ST, MP525 ST user manual Specifications

Page 59

Specifications

All specifications are subject to change without notice.

Optical

Resolution

(MP525 ST)

1024 x 768 XGA

(MP515 ST)

800 x 600 SVGA

Display system 1-CHIP DMD

Lens F/Number

F = 2.6 to 2.8, f = 10 to 12.3 mm

Lamp

220 W lamp

Electrical

Power supply AC100–240V, 2.9 A,

50-60 Hz (Automatic)

Power consumption

329 W (Max); < 1 W (Standby)

Mechanical

Weight

5.5 lbs (2.5 Kg)

Output terminals

Speaker

(Stereo) 5 watt x 2

Control

RS-232 serial control 9 pin x 1

IR receiver x 1

Input terminals

Computer input RGB input

D-Sub 15-pin (female) x 1

Video signal input

S-VIDEO

Mini DIN 4-pin port x 1

VIDEO

RCA jack x 1 SD/HDTV signal input

Analog - Component RCA jack x 3

(through RGB input) Digital - HDMI V1.2 x 1

Audio signal input Audio in

RCA audio jack (L/R) x 2

Environmental Requirements

Operating temperature 0°C–40°C at sea level

Operating relative humidity 10%–90% (without condensation)

Operating altitude 0–1499 m at 0°C–35°C 1500–3000 m at 0°C–30°C (with High Altitude Mode on)

Specifications 59

Image 59
Contents Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Safety Instructions Locations near fire alarms Installation Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewFront/upper side Projector Controls and functionsActivates the selected On-Screen Display OSD menu item Selects an available picture setupMode/Enter ModeDigital Zoom + Remote controlVolume + FreezeTimer Set up Remote control effective rangeReplacing the remote control battery Timer On Up/DownFront Ceiling Positioning your projectorChoosing a location Front TableSelect your screen size Aspect image in a Aspect display areaPositioning your projector Inch Projection dimensionsConnection To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting audio Connecting Video source devicesTo connect the projector to a Component Video source device Connecting a Component Video source deviceConnecting an Hdmi device To connect the projector to an Hdmi deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite Video source deviceBeen applied OperationStarting up the projector Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Correcting keystone Fine-tuning the image size and clarityUsing the remote control Using the OSD menuPreferred language Using the menusUse / to highlight the System Setup Basic menu Press / to select aTo the Security Settings Using a security cable lockUtilizing the password function Setting a passwordWrite down the number and turn off your projector If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Color space Switching input signalChanging Color Space Press Digital Zoom+/- to display the Zoom bar Magnifying and searching for detailsSelecting the aspect ratio About the aspect ratio Optimizing the image Using Wall ColorSelecting a picture mode Adjusting Brightness Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Go to the Picture Picture Mode menuAdjusting Brilliant Color Adjusting ColorAdjusting Tint Adjusting SharpnessTo adjust the settings To highlight Off and press Mode/Enter Setting the presentation timerTo cancel the timer, perform the following steps Hiding the image How to use the Timer On key?Press Mode/Enter Utilizing FAQ functionFreezing the image Highlight Yes and press Mode/Enter to confirm To activate the High Altitude ModeOperating in a high altitude environment Locking control keysPersonalizing the projector menu display Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneShutting down the projector Once the cooling process finishes, a Power Off RingBasic Menu operationMenu system Main menu Sub-menu OptionsAdvanced Informa Description of each menu Color TemperatureSave Settings TimerBlank Timer System Setup Basic menuMenu Settings Auto Power OffSettings On page 27 for details Power On Lock Lamp ModeLamp Settings Reset Lamp Timer Change PasswordFAQ-Image Installation Signal carries closed captionsReset All Returns all settings to the factory preset values SettingsCare of the projector MaintenanceExtending lamp life Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourLamp has been in operation equivalent to Hours Timing of replacing the lampReplacing the lamp Page Restart the projector Resetting the lamp timerLamp time will be reset to Tighten the screw that secures the lampThermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Specifications Mm W x 114 mm H x 236 mm D DimensionsCeiling mount installation Supported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputDisclaimer Limited warrantyCopyright Weee directive Regulation statementsFCC statement EEC statementRegulation statements
Related manuals
Manual 66 pages 8.62 Kb

MP515 ST, MP525 ST specifications

The BenQ MP525 ST and MP515 ST are innovative projectors designed to deliver high-quality visuals for both educational and business environments. With a blend of advanced technologies and user-friendly features, these projectors offer exceptional performance.

Starting with the core characteristics, both models boast DLP (Digital Light Processing) technology, which ensures sharp images with vibrant colors and excellent contrast ratios. The native resolution of these projectors is XGA (1024 x 768), suitable for detailed presentations and videos. The brightness level for the MP525 ST is typically around 2500 ANSI lumens, providing sufficient illumination for well-lit environments. The MP515 ST, while slightly less bright, still delivers adequate performance for dimly lit rooms, making both models versatile for various settings.

One of the standout features of the BenQ MP525 ST is its short-throw projection capability, allowing users to display large images from a short distance. This is particularly beneficial in smaller rooms where space is limited as it minimizes shadows and enables presenters to stay close to their audience. The throw ratio is approximately 0.6:1, meaning it can project a large image within just a few feet from the screen.

Both projectors come equipped with a comprehensive connectivity suite, including HDMI, VGA, S-Video, and composite video inputs, ensuring compatibility with a wide range of devices such as laptops, DVD players, and gaming consoles. They also feature built-in speakers that deliver clear audio without the need for external sound systems, making them convenient for quick setups.

In terms of usability, the BenQ MP525 ST and MP515 ST are designed with user-friendly interfaces and remote controls. They include features like keystone correction to help adjust the image shape, ensuring perfect alignment even when the projector is angled. Additionally, the projector’s lamp life is impressive, reaching up to 4000 hours in economic mode, which reduces the need for frequent replacements and lowers operational costs.

In conclusion, the BenQ MP525 ST and MP515 ST projectors are excellent choices for educators and presenters who require flexibility, quality, and ease of use in their projection equipment. With their advanced DLP technology, short-throw capabilities, and versatile connectivity options, these models cater to diverse presentation needs while ensuring that every image is displayed with clarity and impact.