BenQ MP515 ST, MP525 ST Securing the projector, Using a security cable lock, Setting a password

Page 27

Securing the projector

Using a security cable lock

The projector has to be installed in a safe place to prevent theft. Otherwise, purchase a lock, such as the Kensington lock, to secure the projector. You can locate a Kensington lock slot on the rear side of the projector. See item 11 on page 9 for details.

A Kensington security cable lock is usually a combination of key(s) and the lock. Refer to the lock's documentation for finding out how to use it.

Utilizing the password function

For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu.

WARNING: You will be inconvenienced if you activate the password functionality and subsequently forget the password. Print out this manual (if necessary) and write the password you used in this manual, and keep the manual in a safe place for later recall.

Setting a password

Once a password has been set and the power on lock is activated, the projector cannot be used unless the correct password is entered every time the projector is started.

1.Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security Settings menu. Press Mode/Enter. The Security Settings page displays.

2.Highlight Power On Lock and select On by pressing / .

3.

As pictured to the right, the four arrow keys ( ,

INPUT NEW PASSWORD

 

, , ) respectively represent 4 digits (1, 2, 3,

 

 

4). According to the password you desire to set,

 

 

press the arrow keys to enter six digits for the

 

 

password.

 

4.

Confirm the new password by re-entering the

 

 

new password.

 

Once the password is set, the OSD menu returns

Clear

to the Security Settings page.

 

IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this manual in a safe place.

5.To leave the OSD menu, press Menu/Exit.

Operation 27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Welcome Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Safety Instructions Locations near fire alarms Installation Introduction Projector featuresShipping contents Projector exterior view Front/upper sideRear/lower side Projector Controls and functionsActivates the selected On-Screen Display OSD menu item Selects an available picture setupMode/Enter ModeDigital Zoom + Remote controlVolume + FreezeTimer Set up Remote control effective rangeReplacing the remote control battery Timer On Up/DownFront Ceiling Positioning your projectorChoosing a location Front TableSelect your screen size Aspect image in a Aspect display areaPositioning your projector Inch Projection dimensionsConnection Connecting a computer or monitor Connecting a computerTo connect the projector to a notebook or desktop computer Connecting audio Connecting Video source devicesTo connect the projector to a Component Video source device Connecting a Component Video source deviceConnecting an Hdmi device To connect the projector to an Hdmi deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite Video source deviceOperation Starting up the projectorBeen applied Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Correcting keystone Fine-tuning the image size and clarityUsing the remote control Using the OSD menuPreferred language Using the menusUse / to highlight the System Setup Basic menu Press / to select aTo the Security Settings Using a security cable lockUtilizing the password function Setting a passwordWrite down the number and turn off your projector If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Switching input signal Changing Color SpaceColor space Magnifying and searching for details Selecting the aspect ratioPress Digital Zoom+/- to display the Zoom bar About the aspect ratio Using Wall Color Selecting a picture modeOptimizing the image Adjusting Brightness Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Go to the Picture Picture Mode menuAdjusting Brilliant Color Adjusting ColorAdjusting Tint Adjusting SharpnessTo adjust the settings Setting the presentation timer To cancel the timer, perform the following stepsTo highlight Off and press Mode/Enter Hiding the image How to use the Timer On key?Utilizing FAQ function Freezing the imagePress Mode/Enter Highlight Yes and press Mode/Enter to confirm To activate the High Altitude ModeOperating in a high altitude environment Locking control keysPersonalizing the projector menu display Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneShutting down the projector Once the cooling process finishes, a Power Off RingBasic Menu operationMenu system Main menu Sub-menu OptionsAdvanced Informa Description of each menu Color TemperatureSave Settings TimerBlank Timer System Setup Basic menuMenu Settings Auto Power OffSettings On page 27 for details Power On Lock Lamp ModeLamp Settings Reset Lamp Timer Change PasswordFAQ-Image Installation Signal carries closed captionsReset All Returns all settings to the factory preset values SettingsCare of the projector MaintenanceExtending lamp life Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourLamp has been in operation equivalent to Hours Timing of replacing the lampReplacing the lamp Page Restart the projector Resetting the lamp timerLamp time will be reset to Tighten the screw that secures the lampThermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Specifications Dimensions Ceiling mount installationMm W x 114 mm H x 236 mm D Supported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputLimited warranty CopyrightDisclaimer Weee directive Regulation statementsFCC statement EEC statementRegulation statements
Related manuals
Manual 66 pages 8.62 Kb

MP515 ST, MP525 ST specifications

The BenQ MP525 ST and MP515 ST are innovative projectors designed to deliver high-quality visuals for both educational and business environments. With a blend of advanced technologies and user-friendly features, these projectors offer exceptional performance.

Starting with the core characteristics, both models boast DLP (Digital Light Processing) technology, which ensures sharp images with vibrant colors and excellent contrast ratios. The native resolution of these projectors is XGA (1024 x 768), suitable for detailed presentations and videos. The brightness level for the MP525 ST is typically around 2500 ANSI lumens, providing sufficient illumination for well-lit environments. The MP515 ST, while slightly less bright, still delivers adequate performance for dimly lit rooms, making both models versatile for various settings.

One of the standout features of the BenQ MP525 ST is its short-throw projection capability, allowing users to display large images from a short distance. This is particularly beneficial in smaller rooms where space is limited as it minimizes shadows and enables presenters to stay close to their audience. The throw ratio is approximately 0.6:1, meaning it can project a large image within just a few feet from the screen.

Both projectors come equipped with a comprehensive connectivity suite, including HDMI, VGA, S-Video, and composite video inputs, ensuring compatibility with a wide range of devices such as laptops, DVD players, and gaming consoles. They also feature built-in speakers that deliver clear audio without the need for external sound systems, making them convenient for quick setups.

In terms of usability, the BenQ MP525 ST and MP515 ST are designed with user-friendly interfaces and remote controls. They include features like keystone correction to help adjust the image shape, ensuring perfect alignment even when the projector is angled. Additionally, the projector’s lamp life is impressive, reaching up to 4000 hours in economic mode, which reduces the need for frequent replacements and lowers operational costs.

In conclusion, the BenQ MP525 ST and MP515 ST projectors are excellent choices for educators and presenters who require flexibility, quality, and ease of use in their projection equipment. With their advanced DLP technology, short-throw capabilities, and versatile connectivity options, these models cater to diverse presentation needs while ensuring that every image is displayed with clarity and impact.
Top Page Image Contents