Brother HL-600 manual Remove the old toner cartridge from the printer

Page 43

CHAPTER 5 MAINTENANCE

3. Remove the old toner cartridge from the printer.

Fig. 5-4 Removing the Old Toner Cartridge

☛Caution

Handle the toner cartridge carefully. If toner scatters and your hands or clothes get dirty, wipe or wash it off with cold water immediately.

4.Unpack the new toner cartridge, gently shake it five or six times before installing, and then remove the protective seal.

☛Caution

Only unpack the toner cartridge immediately before installing it into the printer. If toner cartridges are left unpacked for a long period of time, the toner life is shortened.

✔Warning

You can only use a Brother genuine toner cartridge. Using another brand of toner cartridge could void your printer’s warranty.

Fig. 5-5 Shaking the Toner Cartridge and

Remove the Protective Parts

5–3

Image 43

Contents HL-600 Series Shipment of the Printer For USA & Canada Only Laser Printer HL-600 Series User’s GuideCompilation and Publication Notice TrademarksTable of Contents Options Regulations Laser Safety For 110-120 V Model OnlyRadio Interference For 220 240 V Model Only FDA Regulations For Your SafetyIEC 825 Laser Class For 220-240 V Model Only Manufactured at Disconnect deviceCanadian Department of Communications Compliance Statement Important For U.K. only About the Guidebooks Finding Out How to Use the PrinterDefinitions of Warnings, Cautions, and Notes Printer Overview About Your PrinterDpi Resolution and 6ppm Printing Speed FeaturesBi-Directional Parallel Interface Operating and Storage Environment Power SupplyEnvironment USER’S Guide Chapter Paper Handling Paper SpecificationsFan the Paper Straighten the Paper Printable Area MULTI-PURPOSE Sheet Feeder Opening the Feeder Loading Paper or Envelope in the Feeder Loading Paper into the FeederMoving the Paper Guide Closing the Feeder Two Side Printing Manual Duplexing Manual Feed Slot Moving the Paper Guide Opening the Output Tray Extending the Paper Support Wire Output Tray and Paper Support WireReady Lamp LampsData Lamp Alarm LampManual Lamp Select Reset Switch SwitchesSelect Switch Test Switch FF/CONTTEST SwitchReset Switch FF/CONT SwitchReprint Function Sleep ModeManual Test Print ModeReset/Hex Dump Mode USER’S Guide Serial Interface Board Chapter OptionsSelecting the RS-422A Apple Or RS-232C IBM Serial Interface Selecting the RS-422A Apple or RS-232C IBM Serial Interface3 4 5 6 7 Setting the Serial Interface ParametersBits Connecting the Serial Interface Cable 1MB Memory BoardReplacing the Toner Cartridge Chapter MaintenanceRemoving the Multi-Purpose Sheet Feeder Remove the old toner cartridge from the printer Installing the Toner Cartridge Into the Drum Unit Removing the Toner Cartridge Replacing the Drum UnitInside the printer Remove the protective parts ① ⑥ in order as shown below 13 Installing the Drum Unit 14 Adjusting the Print Density Dial Adjusting the Print DensityCleaning the Printer Exterior Cleaning the Printer15 Inside the printer Cleaning the Printer Interior and Drum Unit17 Cleaning the Printer Interior 18 Cleaning the Primary Corona Wire RE-PACKING the Printer 19 Removing the Drum Unit Assembly21 Repacking the Printer USER’S Guide Operator Calls Alarm Indications AT a GlanceUSER’S Guide Troubleshooting Service Calls Locating Paper Jam Position Paper JamsPaper Jam in the Feeder Paper Jam Inside the Printer Setting up the Printer for DOS Setting up the Printer HardwareSetting up the Printer for Windows Setting up the Printer for Apple Macintosh Computers Recommendations Paper HandlingPrinting White Stripes or Faint Images Print QualityWhite Spots 11 Black 13 Stained at Fixed Interval Appendices Printer SpecificationsElectrical and Mechanical FunctionsFig. A-1 Parallel interface cable Parallel Interface SpecificationResident Fonts IBM mode Epson mode HP mode Symbol SETS/ Character SetsHP LaserJet IIP HP LaserJet IIP, Epson FX-850, IBM Propritner XL Appendix-8 Index Index-2 III