Brother HL-600 manual Paper Jam in the Feeder

Page 62

USER’S GUIDE

❏Paper Jam in the Multi-Purpose Sheet Feeder

If a paper jam has occurred inside the multi-purpose sheet feeder, open the multi-purpose sheet feeder to pull up the jammed paper upward out of the feeder; then close the multi-purpose sheet feeder. Also, open the top cover and check that a torn piece doesn’t remain inside the printer referring to the next section.

Fig. 6-3 Paper Jam in the Feeder

If the paper cannot be pulled up, see the next section “Paper Jam

Under the Drum Cover.”

❏Paper Jam under the Drum Cover

If a paper jam has occurred under the drum cover, remove the multi- purpose sheet feeder, open the top cover and the drum cover. Then, pull the jammed paper upwards and out of the printer. Close the covers.

Fig. 6-4 Paper Jam under the Drum Cover

6–6

Image 62

Contents HL-600 Series Shipment of the Printer Laser Printer HL-600 Series User’s Guide For USA & Canada OnlyTrademarks Compilation and Publication NoticeTable of Contents Options Radio Interference For 220 240 V Model Only Laser Safety For 110-120 V Model OnlyRegulations IEC 825 Laser Class For 220-240 V Model Only For Your SafetyFDA Regulations Canadian Department of Communications Compliance Statement Disconnect deviceManufactured at Important For U.K. only Definitions of Warnings, Cautions, and Notes Finding Out How to Use the PrinterAbout the Guidebooks About Your Printer Printer OverviewFeatures Dpi Resolution and 6ppm Printing SpeedBi-Directional Parallel Interface Environment Power SupplyOperating and Storage Environment USER’S Guide Paper Specifications Chapter Paper HandlingFan the Paper Straighten the Paper Printable Area MULTI-PURPOSE Sheet Feeder Loading Paper into the Feeder Opening the Feeder Loading Paper or Envelope in the FeederMoving the Paper Guide Closing the Feeder Two Side Printing Manual Duplexing Manual Feed Slot Moving the Paper Guide Output Tray and Paper Support Wire Opening the Output Tray Extending the Paper Support WireLamps Ready LampManual Lamp Alarm LampData Lamp Select Switch SwitchesSelect Reset Switch FF/CONT Switch FF/CONTTEST SwitchReset Switch Test SwitchSleep Mode Reprint FunctionTest Print Mode ManualReset/Hex Dump Mode USER’S Guide Chapter Options Serial Interface BoardSelecting the RS-422A Apple or RS-232C IBM Serial Interface Selecting the RS-422A Apple Or RS-232C IBM Serial InterfaceSetting the Serial Interface Parameters 3 4 5 6 7Bits Connecting the Serial Interface Cable Memory Board 1MBChapter Maintenance Replacing the Toner CartridgeRemoving the Multi-Purpose Sheet Feeder Remove the old toner cartridge from the printer Installing the Toner Cartridge Into the Drum Unit Replacing the Drum Unit Removing the Toner CartridgeInside the printer Remove the protective parts ① ⑥ in order as shown below 13 Installing the Drum Unit Adjusting the Print Density 14 Adjusting the Print Density DialCleaning the Printer Cleaning the Printer ExteriorCleaning the Printer Interior and Drum Unit 15 Inside the printer17 Cleaning the Printer Interior 18 Cleaning the Primary Corona Wire 19 Removing the Drum Unit Assembly RE-PACKING the Printer21 Repacking the Printer USER’S Guide Alarm Indications AT a Glance Operator CallsUSER’S Guide Troubleshooting Service Calls Paper Jams Locating Paper Jam PositionPaper Jam in the Feeder Paper Jam Inside the Printer Setting up the Printer Hardware Setting up the Printer for DOSSetting up the Printer for Windows Setting up the Printer for Apple Macintosh Computers Paper Handling RecommendationsPrinting Print Quality White Stripes or Faint ImagesWhite Spots 11 Black 13 Stained at Fixed Interval Printer Specifications AppendicesFunctions Electrical and MechanicalParallel Interface Specification Fig. A-1 Parallel interface cableResident Fonts Symbol SETS/ Character Sets IBM mode Epson mode HP modeHP LaserJet IIP HP LaserJet IIP, Epson FX-850, IBM Propritner XL Appendix-8 Index Index-2 III