Brother HL-600 FDA Regulations, For Your Safety, IEC 825 Laser Class For 220-240 V Model Only

Page 8

USER’S GUIDE

FDA Regulations

U.S. Food and Drug Administration (FDA) implemented regulations for laser products manufactured from August 2, 1976. These regulations apply to laser products manufactured from August 1, 1976. Compliance is mandatory for products marketed in the United States. The label shown on the back of the printer indicates compliance with the FDA regulations and must be attached to laser products marketed in the United States.

MANUFACTURED: BROTHER INDUSTRIES, LTD.

15-1 Naeshiro-cho Mizuho-ku Nagoya, 467 Japan

This product complies with FDA radiation performance standards, 21 CFR Subchapter J

Caution

Use of controls, adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure.

For Your Safety

To ensure safe operation the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively grounded through the normal household wiring.

Extension cords used with the equipment must be three-conductor and be correctly wired to provide connection to ground. Incorrectly wired extension cords are a major cause of fatalities.

The fact that the equipment operates satisfactorily does not imply that the power is grounded and that the installation is completely safe. For your safety, if in any doubt about the effective grounding of the power, consult a qualified electrician.

IEC 825 Laser Class (For 220–240 V Model Only)

CLASS 1 LASER PRODUCT.

APPAREIL Å LASER DE CLASSE 1.

LASER KLASSE 1

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

KLASS 1 : LASER

KLASSE 1 LASER PRODUKT

For Finland and Sweden

Varoitus! Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.

Varning – Om apparaten används på annat sätt än i denna Bruksanvisning specificerats, kan användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1.

vi

Image 8

Contents HL-600 Series Shipment of the Printer Laser Printer HL-600 Series User’s Guide For USA & Canada OnlyTrademarks Compilation and Publication NoticeTable of Contents Options Radio Interference For 220 240 V Model Only Laser Safety For 110-120 V Model OnlyRegulations IEC 825 Laser Class For 220-240 V Model Only For Your SafetyFDA Regulations Canadian Department of Communications Compliance Statement Disconnect deviceManufactured at Important For U.K. only Definitions of Warnings, Cautions, and Notes Finding Out How to Use the PrinterAbout the Guidebooks About Your Printer Printer OverviewFeatures Dpi Resolution and 6ppm Printing SpeedBi-Directional Parallel Interface Environment Power SupplyOperating and Storage Environment USER’S Guide Paper Specifications Chapter Paper HandlingFan the Paper Straighten the Paper Printable Area MULTI-PURPOSE Sheet Feeder Loading Paper into the Feeder Opening the Feeder Loading Paper or Envelope in the FeederMoving the Paper Guide Closing the Feeder Two Side Printing Manual Duplexing Manual Feed Slot Moving the Paper Guide Output Tray and Paper Support Wire Opening the Output Tray Extending the Paper Support WireLamps Ready LampManual Lamp Alarm LampData Lamp Select Switch SwitchesSelect Reset Switch FF/CONTTEST Switch Reset SwitchFF/CONT Switch Test SwitchSleep Mode Reprint FunctionTest Print Mode ManualReset/Hex Dump Mode USER’S Guide Chapter Options Serial Interface BoardSelecting the RS-422A Apple or RS-232C IBM Serial Interface Selecting the RS-422A Apple Or RS-232C IBM Serial InterfaceSetting the Serial Interface Parameters 3 4 5 6 7Bits Connecting the Serial Interface Cable Memory Board 1MBChapter Maintenance Replacing the Toner CartridgeRemoving the Multi-Purpose Sheet Feeder Remove the old toner cartridge from the printer Installing the Toner Cartridge Into the Drum Unit Replacing the Drum Unit Removing the Toner CartridgeInside the printer Remove the protective parts ① ⑥ in order as shown below 13 Installing the Drum Unit Adjusting the Print Density 14 Adjusting the Print Density DialCleaning the Printer Cleaning the Printer ExteriorCleaning the Printer Interior and Drum Unit 15 Inside the printer17 Cleaning the Printer Interior 18 Cleaning the Primary Corona Wire 19 Removing the Drum Unit Assembly RE-PACKING the Printer21 Repacking the Printer USER’S Guide Alarm Indications AT a Glance Operator CallsUSER’S Guide Troubleshooting Service Calls Paper Jams Locating Paper Jam PositionPaper Jam in the Feeder Paper Jam Inside the Printer Setting up the Printer Hardware Setting up the Printer for DOSSetting up the Printer for Windows Setting up the Printer for Apple Macintosh Computers Paper Handling RecommendationsPrinting Print Quality White Stripes or Faint ImagesWhite Spots 11 Black 13 Stained at Fixed Interval Printer Specifications AppendicesFunctions Electrical and MechanicalParallel Interface Specification Fig. A-1 Parallel interface cableResident Fonts Symbol SETS/ Character Sets IBM mode Epson mode HP modeHP LaserJet IIP HP LaserJet IIP, Epson FX-850, IBM Propritner XL Appendix-8 Index Index-2 III