Linksys PAP2-VU Application Start and End Protocol IP Address Enable, Internet phone 5060 to

Page 22

Phone Adapter with 2 Ports for Voice-over-IP

8. Repeat steps 5-7 until you have entered all four port ranges for the Phone Adapter.

Application

Start and End

Protocol

IP Address

Enable

 

 

 

 

 

Internet phone 1

5060 to 5061

UDP

(IP address of

X

 

 

 

Phone Adapter)

 

 

 

 

 

 

Internet phone 2

53 to 53

UDP

(IP address of

X

 

 

 

Phone Adapter)

 

 

 

 

 

 

Internet phone 3

69 to 69

UDP

(IP address of

X

 

 

 

Phone Adapter)

 

 

 

 

 

 

Internet phone 4

10000 to 20000

UDP

(IP address of

X

 

 

 

Phone Adapter)

 

 

 

 

 

 

9.Check the Enable option for the port services you want to use.

10.When you have completed the configuration, click the Save Settings button.

2.When I make a telephone call, the call doesn’t go through; instead, I hear a fast busy signal. Go through this checklist until your problem is solved:

Follow these instructions to reboot your cable or DSL modem, Phone Adapter, and router:

1.Power off your cable or DSL modem by unplugging its power adapter.

2.Power off the router by unplugging its power adapter.

3.Power off the Phone Adapter by unplugging its power adapter.

4.Wait two minutes, and then power on your cable or DSL modem by plugging its power adapter into an electrical outlet.

Appendix A: Troubleshooting

17

Common Problems and Solutions

Image 22
Contents Phone Adapter Division of Cisco Systems, IncPage How to Use this Guide Copyright and TrademarksTable of Contents Back Panel Front PanelWelcome IntroductionWhat’s in this Guide? What’s in this Guide? Getting to Know the Phone Adapter Back Panel PortsPhone Adapter’s LEDs are located on the front panel Front PanelPhone is being used or an incoming call has been detected Overview Connecting the Phone AdapterInstructions for Connecting the Phone Adapter InternetConnect the Telephone Cable Remove the plate from the Phone Adapter’s bottom panel Placement OptionsStand Option Phone Adapter’s Interactive Voice Response MenuWall-Mount Option Measurement between Wall-Mount SlotsAccessing the Interactive Voice Response Menu Using the Phone Adapter’s Interactive Voice Response MenuUsing the Interactive Voice Response Menu Not press any other keys until you Use this command to enter Response MenuInteractive Voice Response Menu Key or hang up to exitEnter 0 to disable Has been enabled or disabled. If101 Enter 1 to enable Check Dhcp 100Subnet Mask Mask using Address usingStatic IP address When entering a Decimal point Network mask When entering a Decimal pointPhone Adapter Manual Reboot 732668 Address Address usingStatic gateway IP address When entering a Decimal point 131 Enter the IPConfiguring the Settings for Your Internet Phone Service Appendix a Troubleshooting Common Problems and SolutionsAppendix a Troubleshooting IP address Phone Adapter Internet phone 53 to Application Start and End Protocol IP Address EnableInternet phone 5060 to IP address Phone Adapter Internet phone 69 toPhone Adapter with 2 Ports for Voice-over-IP Application Start and End Protocol IP Address Enable Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Application Start and End Protocol IP Address Enable Frequently Asked Questions Pick up the phone and dial as you normally wouldCan I make calls while I’m browsing the Internet? Shared Resources Appendix B Windows HelpNetwork Neighborhood/My Network Places Appendix B Windows Help Appendix C Glossary Appendix C Glossary Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Phone Adapter with 2 Ports for Voice-over-IP Appendix D Specifications Storage Humidity DimensionsMm x 101 mm x 15 mm Appendix E Warranty Information Limited WarrantyAppendix E Warranty Information Appendix F Regulatory Information FCC StatementAppendix F Regulatory Information Appendix G Contact Information Appendix G Contact Information