Linksys EG0801SK manual Network Neighborhood is Empty, You receive Dhcp Errors in Windows

Page 36

Instant Gigabit Series

5.On the Access Control Tab, User Level Access is selected, but Shared Level Access is grayed out and not accessible.

•You previously had your primary network logon set to Client for NetWare Networks. On the Configuration tab of the Network Properties window, ensure that your primary network logon is set to Client for Microsoft Networks.

•Your personal web server PC or Microsoft Front Page may require you to choose a user level for security reasons.

6.In Network Neighborhood you can only see yourself and no other computers on the network.

•Make sure that the cables are connected correctly. Make sure you are get- ting Link or Activity lights on both the EtherFast Card and your hub. Try changing to a new cable that you know is working.

•Your workgroup name may be different from other computers on your net- work. Make sure each PC on the network is using the same workgroup name and protocol.

•Try using the Find Computer function.

7.In Network Neighborhood, you can see all other computers on the network but not yourself, and all other computers can see each other and not your comput- er.

•You may not have enabled File and Printer Sharing.

•The network card might not be setup properly. Try reinstalling the card’s drivers. To clean your system of the old installation, follow the procedure in the Starting Over in Windows 95, 98, Millennium or 2000 section and then re-install.

8.Network Neighborhood is Empty.

•Verify that your Microsoft Client is installed. See the Windows 95 or 98 setup instructions in this guide for directions. Verify that you have logged in correctly. Refresh the screen by pressing F5 several times.

9.You receive DHCP Errors in Windows.

•If you are connecting to a DHCP server, check your cabling connection. If your network requires TCP/IP, check with your network administrator or your Windows documentation for proper settings.

•If you don’t have a DHCP server on your network and your network does not require TCP/IP, you may remove the TCP/IP Protocol from Windows’ networking. To do this, click on Start, Settings, Control Panel, then dou- ble-click on Network. Click once on the component entry with the words TCP/IP and Linksys or TCP/IP, then click on the Remove button. Click OK when finished and restart your PC.

EtherFast® 10/100/1000 8+1 Workgroup GigaSwitch Starter Kit

10.In Network Neighborhood you can only see computers running the same oper- ating system as your computer (i.e., your PC is running Windows 95 and it can only see other Windows 95 computers and not any computer running Windows 98).

•Choose Start, Find, Computer and type the name of the computer in the Network Neighborhood window that appears and click Find Now.

•Next, make sure that the you are using the same protocol(s) and workgroup name on the 95 and 98 computers. To do this, click Start, Settings, Control Panel on two computers running different Windows operating systems. Click on the Network icon, choose the Configuration tab, then click on the Identification tab for Workgroup name. Compare the protocols on both computers and make sure that they are the same. If any protocols are miss- ing, refer to page 60 to install any needed protocol(s).

•If all computers are using the same protocol(s) and Workgroup name, and Windows 95 computers can't see Windows 98 computers, enable NetBIOS on all the computers using Windows 95 and 98. Follow these instructions:

•The IPX/SPX-compatible protocol should be installed on all Windows com- puters (see the Manually Installing the Network Components in Windows 95, 98, and Millennium section if you need to add this proto- col). Bring up the properties of the IPX/SPX-compatible protocol by click- ing on Start, Settings, Control Panel, then double-click the Network icon. Choose the Configuration tab and highlight IPX/SPX-compatible Protocol. Click on Properties. Now, to install NetBIOS, click on the NetBIOS tab. Put a check next to I want to enable NetBIOS over IPX/SPX. Click OK, then OK again. Windows will copy the appropriate files to your computer. When asked to restart your PC, remove any floppy disks and click OK. Be sure to do this on all of your computers that are having trouble seeing your entire network.

11.The workgroup, protocols, cabling and driver are all working properly, but the PC uses an AMD processor and it can only see itself in network neighborhood.

•In some instances with PCs using AMD processors, the IRQ assigned to the card by the BIOS (as it gets listed on the bootup screens of most PCs) does- n't correspond to the IRQ assigned by Windows. This can be fixed by dis- abling the IRQ holder for PCI Steering in the Windows Device Manager. Refer to your PC's documentation for instructions or you can follow the suggested instructions below. Keep in mind that this procedure will vary depending on your computer’s configuration.

•Click on Start, Settings, Control Panel, then double click the System icon. Click on the Device Manager tab. Open System Devices, then open PCI Bus.

65

66

Page 35 Page 37
Image 36
Page 35 Page 37
Contents EtherFast 10/100/1000 +1 Workgroup GigaSwitch Starter Kit Copyright & Trademarks Contents Your EtherFast 10/100/1000 8+1 Workgroup Gigaswitch FeaturesPackage Contents Introduction10/100/1000 Workgroup GigaSwitch’s Rear Panel GigaSwitchPower 10/100/1000 Workgroup GigaSwitch’s Front PanelSwitches Versus Hubs Planning Your NetworkLEDs RJ-45 PortWhere to Install the Instant Gigabit Network Adapter Installing The Instant Gigabit Network Adapter Installing the Network Card & CablingRemove your computers outside cover Installing The Workgroup Gigaswitch Connecting Computers To Your SwitchUplinking to Other Switches and Hubs Connecting Your Hardware Together and Booting UpInstalling the Drivers for Windows Tips on Switching Your NetworkVersion a Version B also known as OSR2 Installing the Driver in Windows 95 Version B Installing the Network Adapter’s Driver Instant Gigabit Series Installing the Drivers for Windows Millennium Installing the Network Adapter’s DriversInstant Gigabit Series Windows NT 4.0 Installation & Setup Installing NT Networking and the Network Adapter Driver Instant Gigabit Series Page Instant Gigabit Series \i386 Installing the Drivers for Windows Completing the Found New Hardware Wizard dialog box will Advanced Properties Configuring The Instant Gigabit Network Adapter Configuring the Adapter for Windows 95, 98, and MillenniumConfiguration tab Click on Appendix Sharing Your Files and PrintersOverview Enabling File SharingInstalling the Driver in Windows 95 Version a Enabling Printer SharingNetWare portion of your Windows setup is complete Starting Over in Windows 95, 98, or MillenniumInstant Gigabit Series Starting Over in Windows Manually Installing the Network Components in Windows Click on Start, Settings, then Control Panel IPX/SPX-compatible ProtocolNetBEUI Client for Microsoft NetworksInstalling and Configuring Wake-On-LAN Motherboard SupportAbout Plug-and-Play PCI Technology Troubleshooting Linux, Open Source and Beta Operating SystemsTwisted-Pair Cabling You receive Dhcp Errors in Windows Network Neighborhood is EmptyGlossary Instant Gigabit Series Instant Gigabit Series Instant Gigabit Series Specifications Specifications for EG1032Specifications for EG0801W EnvironmentalWarranty Information Tech Support and RMA Issues FaxContact Information InformationT p / / w w w. l i n k s y s . c o m

EG0801SK specifications

The Linksys EG0801SK is an advanced 8-port Ethernet switch designed to provide high-performance networking solutions for small to medium-sized enterprises, home offices, or any environment requiring reliable connectivity. Combining speed, performance, and versatility, this switch is an essential component for users looking to expand their local network efficiently.

The EG0801SK operates on a non-blocking architecture, ensuring that each port can handle consistent data transfer rates without interference. This is crucial for environments where multiple devices are connected simultaneously, as it guarantees minimal latency and efficient bandwidth utilization. With support for 10/100/1000 Mbps speeds, the switch is fully compatible with various devices, including computers, printers, and IP cameras, facilitating smooth communication across the network.

One of the standout features of the Linksys EG0801SK is its switch fabric that offers a high throughput. This means that it can handle burst traffic without any drops, ensuring that data-heavy applications can run uninterrupted. With Auto-MDI/MDIX support, users need not worry about the type of cables used; the switch automatically detects and adjusts, simplifying installation processes and reducing setup time.

In addition to its performance capabilities, the EG0801SK incorporates energy-efficient technologies that help reduce power consumption. The device uses energy-saving features such as "Green Ethernet," which adjusts power usage according to the number of connected devices and their respective activity levels. This makes the EG0801SK an environmentally friendly option, appealing to businesses looking to reduce their carbon footprint.

The sleek design of the Linksys EG0801SK allows it to fit seamlessly into any office environment, whether mounted on a wall, placed on a desk, or incorporated into a server rack. The switch is also equipped with LEDs for port status monitoring, providing users with real-time insights into connectivity and operation status.

In conclusion, the Linksys EG0801SK is a robust, feature-rich Ethernet switch that stands out due to its performance, reliability, and energy efficiency. It is designed to meet the demands of today's networking needs while ensuring ease of use and maintenance, making it an ideal choice for any networking environment.
Top Page Image Contents