Delta Tau 3Ax-602646-xUxx manual Protection

Page 10

Quad Amp Hardware Reference Manual

Protection

There are several layers of protection built into the amplifier, including transient voltage filters, transient surge suppressors, fuses, a flyback diode, and a variety of fault detection circuits. These are discussed in the following paragraphs and in the Troubleshooting Chapter.

Transient Voltage Filter

The transient voltage RC filter is used as a means of suppressing inductive transients and is located across the single phase Control AC input voltage connector C3.

Transient Surge Suppressors

Transient surge suppressors (also referred to as metal oxide varistors or MOVs) are connected across all three input phases (L1, L2, L3) of the Main AC input power. They are located on a circuit board attached to the top of the bridge power rectifier. The primary function of these devices is to absorb high-level energy pulses (spikes).

Fly-Back Diode

The fly-back diode clamps inductive spikes that may be generated across the external shunt resistors when the shunt IGBT is turned off. The diode is connected across the external shunt resistor terminals.

Fuses

The primary hardware protection is fuses, which are mounted within the Quad Amplifier chassis.

Fuse F201

F201 is a 30 Amp long delay fuse, located externally on the top cover of the Quad Amplifier. Fuse F201 is connected to the output of the shunt regulator IGBT and to the internal shunt regulator resistors. Fuse F201 protects the shunt regulator IGBT and the internal shunt resistors from over current damage.

Fuse F202

F202 is a 4-Amp Slo-Blo fuse located under the Quad Amplifier cover, next to the control AC input power supply transformer. This fuse is connected between incoming AC control input power connector C3 and control input AC power transformer T201. Fuse F202 protects the primary input windings of the control power supply transformer against overloads.

Ground Fault (GF)

The Ground Fault Detector is a self-powered circuit that continuously samples the AC line currents via a toroid around the incoming three phase lines. If there is more current flowing into the amplifier than out, the ground fault circuit will activate and shut down the Quad Amplifier with a soft start fault.

6

Introduction

Image 10
Contents Quad Amp Copyright Information Delta Tau Data Systems, Inc. Technical SupportTable of Contents Jumpers, Potentiometers, Test Points, and LEDs Introduction Safety SummaryLive Circuit Contact Procedures Related Technical DocumentationElectrical Specifications Quad Amp Basic SpecificationsPhysical Specifications Bus Supply, Control Supply and Shunt Specifications380/460/480V Quad Amplifier Specifications Output Specifications for 120/208/230 VAC Amplifier Quad Amp SpecificationsOutput Specifications for 380/460 VAC Amplifier Protection Description Configurable OptionsPower Blocks Description Mounting Options DescriptionAccessories Description ACC8FReceiving and Handling Installation Considerations and OptionsGetting Started Equipment RequiredMultiple Units Heat DissipationVibration Operation ConfigurationTheory of Operation Logic BoardFiring Boards DC Bus Power SupplyCurrent Sense Board Soft Start and Shunt RegulatorHeat Dissipation Shunt ConsiderationsQuad Amp Hardware Reference Manual Theory of Operation Typical Quad Amplifier Setup InstallationWiring the Quad Amplifier System Quad Amplifier Channel ConnectionsAccessory Terminal Board Acc-8F, Acc-24E2 PWM Input Cables Non-Standard Quad Amplifier SetupConnecting Power Devices ConnectorsTOP View Pin# Symbol Function Description Main AC Input Power Control AC Input VoltageFor 460 VAC Operation For 480 VAC OperationMotor Wiring Bus Power Enable/Emergency StopBus Filter/Indicator Shunt and BusName Position Description Default Symbol DescriptionCurrent Sense Board Jumper and LED Locations Symbol` Description Tp Factory Set LOWPMAC2 I-Variables Setup GroundingP2Setup Start-Up ProceduresPower On Sequence P2Setup Functions208/230 VAC 380/460 VACQuad Amp Hardware Reference Manual Logic Fault Detection and Fault Codes TroubleshootingFault Reporting Global and Axis-Specific Faults LED Fault IndicatorGlobal Fault Only Axis-Specific Fault OnlyProblem Check Corrective Action Quad Amp Hardware Reference Manual Purpose Illustrated Repair Parts ListHow to Use the Repair Parts List ScopeDelta Tau Data Systems 4 Axis Digital Amplifier Part Number Description 3 4 5 6 Index Qty Per Assy Manu Part Number Facturer0HM

3Ax-602646-xUxx specifications

Delta Tau 3Ax-602646-xUxx is a cutting-edge motion controller designed for precision applications in automation and robotics. This model exemplifies advanced technology and innovative design, catering to industries ranging from manufacturing to aerospace. One of the key features of the Delta Tau 3Ax-602646-xUxx is its capability to control three axes simultaneously, allowing for synchronous motion that is critical in high-speed applications.

At the core of its functionality is its robust processing unit, which supports high-speed data handling and complex algorithms for motion control. This allows the user to achieve precise positioning and trajectory control, essential for tasks such as CNC machining or robotic arms. The controller operates with real-time feedback, ensuring that any deviations in motion are corrected instantly, thereby enhancing reliability and performance.

The Delta Tau 3Ax-602646-xUxx incorporates a user-friendly interface, which simplifies the programming of motion sequences. Its compatibility with various programming languages and protocols such as C, C++, and PLC languages makes it an adaptable choice for engineers. Furthermore, it supports a range of standard communication protocols, enabling seamless integration with existing systems and devices.

One of the standout technological features of this controller is its adaptive control strategy. This allows the system to learn from past operations and adjust its parameters to optimize performance, making it suitable for applications that require high levels of precision and repeatability. The Delta Tau 3Ax-602646-xUxx also utilizes advanced algorithms for PID control, ensuring smooth acceleration and deceleration, which is vital for maintaining component integrity in delicate manufacturing processes.

Another significant characteristic is its ability to interface with a variety of sensors and feedback devices, providing enhanced environmental awareness. This feature significantly boosts the controller's versatility as it can adapt to different machinery and operational challenges easily. Additionally, the system is designed to be scalable, accommodating future upgrades or expansions, thus offering long-term investment value for businesses.

In summary, the Delta Tau 3Ax-602646-xUxx is a powerful motion controller that combines precision, versatility, and advanced technology. Its simultaneous axis control, robust processing capabilities, user-friendly interface, and adaptive features make it an essential tool for modern automation and robotics applications, ensuring high levels of efficiency and productivity.