8e6 Technologies TAR 1.0 quick start Hardware Component Specifications, Fcc

Page 48

Hardware Component Specifications

Specification

“S” Value

“H” Value

“MSA” Value

Operating temperature

10° C ~ 35° C (50° F

10° C ~ 35° C (50°

10° C ~ 35° C (50° F

range

~ 95° F)

F ~ 95° F)

~ 95° F)

Storage temperature range

-40° C ~ +60° C (-

-40° C ~ +60° C (-

-40° C ~ +70° C (-

 

40° F ~ 158° F)

40° F ~ 158° F)

40° F ~ 158° F)

Operating humidity range

8 ~ 90% non-con-

8 ~ 90% non-con-

8 ~ 90% non-con-

 

densing

densing

densing

Storage humidity range

5 ~ 95% non-con-

5 ~ 95% non-con-

5 ~ 95% non-con-

 

densing

densing

densing

Power supply

260W AC power

560W Hot-swap

Thermal control

 

supply [24-pin, (4-pin

redundant AC

260W AC power

 

= 12V)]

power supply with

supply with PFC

 

 

PFC [ 24-pin, (8-pin

[ 24-pin, (4-pin =

 

 

= 12V) ]

12V) ]

Rated AC input voltage

100 ~ 240V,

100 ~ 240V, 60-

100 ~ 240V, 60-

 

50/60Hz, 5-3 Amp

50Hz, 10-5 Amp

50Hz, 5-3 Amp

 

 

per power supply

 

 

 

module (two mod-

 

 

 

ules included in the

 

 

 

chassis)

 

Rated input frequency

50 ~ 60 Hz

50 ~ 60 Hz

50 ~ 60 Hz

Rated input current

5A MAX

10A (115V) to 5A

5A MAX

 

 

(230V)

 

Rated output power

260W

560W

260W

Maximum rated BTU

1370 BTUs/Hr

N/A (see specs

N/A (see specs

 

 

below)

below)

Nominal DC output: +3.3V

15.0A

21.0A

15.0A

Nominal DC output: +5V

25.0A

30.0A

25.0A

Nominal DC output: +12V

18.0A

42.0A

18.0A

Nominal DC output: -12V

1.0A

1.0A

1.0A

Nominal DC output: +5V

2.0A

4.0A

2.0A

standby

 

 

 

Regulatory (power supply)

Power Supply Safety

EN 60950/IEC

USA - UL listed,

 

/ EMC USA - UL

60950-Compliant

FCC

 

listed, FCC Canada

UL Listed (USA)

Canada - CUL listed

 

- CUL listed

CUL Listed (Can-

Germany - TUV

 

Germany - TUV

ada)

Certified

 

Certified

TUV Certified (Ger-

Europe/CE Mark

 

Europe/CE Mark

many)

EN 60950/IEC

 

EN 60950/IEC

 

60950-Compliant

 

60950-Compliant

 

 

iv

8e6 Threat Analysis Reporter Quick Start Guide

Image 48 Contents
Guide 8e6 Threat Analysis Reporter Quick Start Guide Contents 8e 6 Threat Analysis Reporter Quick Start Guide Threat Analysis Reporter Introduction About this Document Conventions Used in this DocumentProcedures 8e6 Corporate Headquarters USA8e6 Taiwan Unpack the Unit from the Carton Rack Setup Suggestions Install the Chassis RailsRack Mount the S or MSA Server Rack Mount InstructionsInstall the Rack Rails Install the Server into the RackInstalling the Server into a Telco Rack Install the H Server Bezel 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide Install the Inner Rails Install the Outer RailsRack Mount the H Server Install the Server into the Rack Installing the Server into a Telco Rack Initial Setup Procedures Monitor and Keyboard Setup Serial Console SetupLink the Workstation to the Threat Analysis Reporter HyperTerminal Setup Procedures 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide Step-by-Step Initial Setup Procedures Login screen, password prompts#s3tup#r3k Configure Network Interface screen 8e6 Threat Analysis Reporter Quick Start Guide Configure default gateway screen Configure Domain Name Servers screenConfigure Host Name screen Time zone regional configuration screen Configure Wizard user screen Setup Wizard Confirmation screen Administration menuSystem Status Screen Log Off, Disconnect the PeripheralsPhysically Connect the Unit to the Network Bandwidth ManagementWizard Setup Procedures Access the Threat Analysis Reporter Administrator ConsoleLog in to the Threat Analysis Reporter Administrator Console Register administrator 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide Register R3000 & ER R30008e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide 8e 6 Threat Analysis Reporter Quick Start Guide Register Gauges Specify Gauge Groups to be MonitoredView, Edit Gauge Components Server Settings Conclusion Physical Specifications Internal Product SpecificationsHardware Component Specifications FCCMSA Front Panel LED Indicators, Buttons Diagrams and DescriptionsLED Indicators and Buttons LED Indicator KeyPreliminary Setup Procedures Other Required Installation ItemsUnpack the Ethernet Tap Unit from the Box Install the Ethernet Tap Unit Ports in front panel of NetOptics 10/100BaseT Tap Tap Installation
Related manuals
Manual 54 pages 32.58 Kb