ADTRAN system manual Default password for the Tracer 5045 is tracer

Page 46

Section 5 User Interface Guide	TRACER 5045 System Manual

>TRACER SYSTEM CONFIGURATION > SITE NAME

Provides a user-defined alphanumeric description (up to 25 characters) for the TRACER 5045 system.

>TRACER SYSTEM CONFIGURATION > MODEM CONTROL

Configures the modem control leads on the RS-232 port (terminal interface located on the rear panel of the unit). Set MODEM CONTROL to ENABLED when connecting the unit to a modem (using a null modem adapter). Setting MODEM CONTROL to DISABLED prevents the TRACER 5045 from monitoring DCD and enables data to be sent to the VT100 continuously. MODEM CONTROL must be set to DISABLED when the VT100 terminal is in use. The TRACER 5045 comes factory programmed with MODEM CONTROL set to

DISABLED.

Press <Ctrl+Z> three times from the terminal interface to disable MODEM CONTROL when the modem control leads are active.

>TRACER SYSTEM CONFIGURATION > MODEM CONNECTION (LOGOUT)

Causes the TRACER 5045 to de-assert Clear To Send (CTS) and DSR for a time greater than 20 msec. This signals the modem to disconnect the analog connection. Hangup-On-DTR-Drop may need to be explicitly enabled on some modems. If PASSWORD PROTECTION is ENABLED, this menu also causes the unit to close the current session and return to the TRACER System Status menu page and wait for password input.

>TRACER SYSTEM CONFIGURATION > PASSWORD ENABLE

Configures password protection for the VT100 terminal interface. Password protection for the TRACER 5045 requires password input from the TRACER 5045 System Status menu page when connecting to the unit. When configured for password protection, the TRACER 5045 closes any terminal session that remains inactive for more than 10 minutes. The TRACER 5045 comes factory programmed

with PASSWORD ENABLE set to DISABLED.

>TRACER SYSTEM CONFIGURATION > PASSWORD

Sets the password for password protection of the TRACER 5045 VT100 terminal interface. Enter up to 8 alphanumeric characters. The system password is case sensitive.

The default password for the TRACER 5045 is tracer.

>TRACER SYSTEM CONFIGURATION > PERFORMANCE STATS (CLEAR)

Resets all system error counters for the TRACER 5045.

46

© 2003 ADTRAN, Inc.

612805045L1-1A

Image 46

Contents Tracer To the Holder of the Manual TrademarksAbout this Manual Revision History Safety Instructions Save These Important Safety InstructionsFCC-Required Information Radio Frequency Interface StatementFCC Output Power Restrictions Exposure to Radio Frequency FieldsRepair and Return Pre-Sales Inquiries and Applications SupportPost-Sale Support Installation and Maintenance SupportTraining Table of Contents Table of Contents Tracer 4208 System Manual System Description System Overview Features and BenefitsConfiguration and Management OperationalReceiver Sensitivity Antenna Information Receiver PowerLine-of-Site Other ConsiderationsMicrowave Path Engineering Basics Tracer 5045 System Manual Decibels LINE-OF-SITETerminology Calculating the Fade MarginReceiver Power Transmitted Power PT Antenna GainPath Distance d Carrier Wavelength λSystem Losses L Path Loss LP Typical Coaxial Loss for Common Cable TypesAntenna Alignment Receiver SensitivityAntenna Information Path Loss for Given Path Lengths MilesAntenna Beam Patterns Tracer Rssi Test PointsFresnel Zones, Earth Curvature, & Antenna Heights Minimum Antenna Height for Given Path Lengths Terrain Terrain Factor Description Other ConsiderationsPath Availability Climate Climate Factor DescriptionMicrowave Path Engineering Basics Tracer 5045 System Manual At-A-Glance Specifications Reviewing the Front Panel DesignReviewing the Front Panel Design Equipment DimensionsPower Requirements Rssi Monitoring InterfaceReviewing the Tracer 5045 Rear Panel Design RS-232 Connection DB-25 Terminal Use Rear Panel Description Name ConnectorRS-232 Connection Pinout RS-232 Connection Modem Use Tracer 5045 DCE to Terminal DTE Diagram DB-25Tracer 5045 DCE to Personal Computer DB-9 Tracer 5045 DCE to Modem DCE DB-25 Alarm Contacts Plug-In Terminal Block10/100BaseT/TX Connections RJ-48C 100BaseT/Tx Interface PinoutAT-A-GLANCE Specifications DC Power Connection Plug-In Terminal BlockAntenna Interface N-Type connector FuseHardware Description Specification Transmitter Hardware Description Specification Power Engineering Guidelines Tracer 5045 System Manual Network Turnup Procedure Unpack and Inspect the SystemTools Required Contents of Adtran ShipmentIntroduction Unpack and Inspect the SystemChannel Selection Grounding InstructionsConnecting the Ethernet Interfaces Supplying Power to the UnitMounting Options Terminal Menu and System Control Navigating the Terminal MenuMenu Descriptions Navigating the Terminal Menu Terminal Menu WindowTerminal Menu and System Control Navigating using the Keyboard KeysPassword Protection To do this Press this keyMenu Descriptions Contact InformationRF Status Rx PowerTx Power Ethernet StatusMain Menu Tracer System Configuration Default password for the Tracer 5045 is tracer Tracer Link Performance History Ethernet Switch Status Ethernet Switch Status RX Packets Dropped User Interface Guide Tracer 5045 System Manual Installing/Troubleshooting the Tracer Hardware OverviewTST LED LED Indicators PWR LEDOverview RF Down LEDRF LOW LED RF ErrorsSTEP-BY-STEP Troubleshooting LAN LEDsINSTALLING/TROUBLESHOOTING the Tracer Hardware Installing/Configuring Ethernet Hardware Troubleshooting Guide Tracer 5045 System Manual