ADTRAN 5045 system manual FCC-Required Information, Radio Frequency Interface Statement

Page 5

TRACER 5045 System Manual

FCC-Required Information

 

 

FCC-Required Information

Federal Communications Commission Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio frequencies. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Shielded cables must be used with this unit to ensure compliance with Class A FCC limits.

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Radio Frequency Interface Statement

This equipment has been tested and found to comply with the limits for an intentional radiator, pursuant to Part 15, Subpart C of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause interference to radio communications.

The limits are designed to provide reasonable protection against such interference in a residential situation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna of the affected radio or television.

Increase the separation between the equipment and the affected receiver.

Connect the equipment and the affected receiver to power outlets on separate circuits.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by ADTRAN could void the user’s authority to operate the equipment.

612805045L1-1A

© 2003 ADTRAN, Inc.

5

Image 5
Contents Tracer About this Manual TrademarksTo the Holder of the Manual Revision History Save These Important Safety Instructions Safety InstructionsRadio Frequency Interface Statement FCC-Required InformationExposure to Radio Frequency Fields FCC Output Power RestrictionsPre-Sales Inquiries and Applications Support Repair and ReturnTraining Installation and Maintenance SupportPost-Sale Support Table of Contents Table of Contents Tracer 4208 System Manual System Description Configuration and Management Features and BenefitsSystem Overview OperationalLine-of-Site Receiver PowerReceiver Sensitivity Antenna Information Other ConsiderationsMicrowave Path Engineering Basics Tracer 5045 System Manual Terminology LINE-OF-SITEDecibels Calculating the Fade MarginReceiver Power Antenna Gain Transmitted Power PTSystem Losses L Carrier Wavelength λPath Distance d Typical Coaxial Loss for Common Cable Types Path Loss LPAntenna Information Receiver SensitivityAntenna Alignment Path Loss for Given Path Lengths MilesFresnel Zones, Earth Curvature, & Antenna Heights Tracer Rssi Test PointsAntenna Beam Patterns Minimum Antenna Height for Given Path Lengths Path Availability Other ConsiderationsTerrain Terrain Factor Description Climate Climate Factor DescriptionMicrowave Path Engineering Basics Tracer 5045 System Manual Reviewing the Front Panel Design At-A-Glance SpecificationsPower Requirements Equipment DimensionsReviewing the Front Panel Design Rssi Monitoring InterfaceReviewing the Tracer 5045 Rear Panel Design RS-232 Connection Pinout Rear Panel Description Name ConnectorRS-232 Connection DB-25 Terminal Use Tracer 5045 DCE to Personal Computer DB-9 Tracer 5045 DCE to Terminal DTE Diagram DB-25RS-232 Connection Modem Use 10/100BaseT/TX Connections RJ-48C Alarm Contacts Plug-In Terminal BlockTracer 5045 DCE to Modem DCE DB-25 100BaseT/Tx Interface PinoutAntenna Interface N-Type connector DC Power Connection Plug-In Terminal BlockAT-A-GLANCE Specifications FuseHardware Description Specification Transmitter Hardware Description Specification Power Engineering Guidelines Tracer 5045 System Manual Unpack and Inspect the System Network Turnup ProcedureIntroduction Contents of Adtran ShipmentTools Required Unpack and Inspect the SystemGrounding Instructions Channel SelectionMounting Options Supplying Power to the UnitConnecting the Ethernet Interfaces Menu Descriptions Navigating the Terminal MenuTerminal Menu and System Control Terminal Menu Window Navigating the Terminal MenuPassword Protection Navigating using the Keyboard KeysTerminal Menu and System Control To do this Press this keyContact Information Menu DescriptionsTx Power Rx PowerRF Status Ethernet StatusMain Menu Tracer System Configuration Default password for the Tracer 5045 is tracer Tracer Link Performance History Ethernet Switch Status Ethernet Switch Status RX Packets Dropped User Interface Guide Tracer 5045 System Manual Overview Installing/Troubleshooting the Tracer HardwareOverview LED Indicators PWR LEDTST LED RF Down LEDSTEP-BY-STEP Troubleshooting RF ErrorsRF LOW LED LAN LEDsINSTALLING/TROUBLESHOOTING the Tracer Hardware Installing/Configuring Ethernet Hardware Troubleshooting Guide Tracer 5045 System Manual