ADTRAN 5045 system manual FCC Output Power Restrictions, Exposure to Radio Frequency Fields

Page 6

FCC-Required Information	TRACER 5045 System Manual

FCC Output Power Restrictions

The FCC does not require licensing to implement this device. License-free operation in the industrial, scientific, and medical band is documented in FCC Rules Part 15.247. It is the responsibility of the individuals designing and implementing the radio system to assure compliance with any pertinent FCC Rules and Regulations. This device must be professionally installed.

Exposure to Radio Frequency Fields

The TRACER 5045 is designed to operate at 5.8 GHz with 100 mW maximum transmit power.

This level of RF energy is below the Maximum Permissible Exposure (MPE) levels specified in FCC OET 65:97-01. The installation of high gain antenna equipment in the system configuration may create the opportunity for exposure to levels higher than recommended for the general population at a distance less than 15 feet (4.6 meter) from the center of the antenna. The following precautions must be taken during installation of this equipment:

•The installed antenna must not be located in a manner that allows exposure of the general population to the direct beam path of the antenna at a distance less than 15 feet (4.6 meters). Installation on towers, masts, or rooftops not accessible to the general population is recommended; or

•Mount the antenna in a manner that prevents any personnel from entering the area within 15 feet (4.6 meter) from the front of the antenna.

•It is recommended that the installer place radio frequency hazard warnings signs on the barrier that prevents access to the antenna.

•Prior to installing the antenna to the TRACER 5045 output, make sure the power is adjusted to the settings specified in section 2 of this manual.

•During antenna installation, be sure that power to the TRACER equipment is turned off in order to prevent any energy presence on the coaxial connector.

•During installation and alignment of the antenna, do not stand in front of the antenna assembly.

•During installation and alignment of the antenna, do not handle or touch the front of the antenna.

These simple precautions must be taken to prevent general population and installation personnel from exposure to RF energy in excess of specified MPE levels.

6

© 2003 ADTRAN, Inc.

612805045L1-1A

Image 6

Contents Tracer Trademarks To the Holder of the ManualAbout this Manual Revision History Safety Instructions Save These Important Safety InstructionsFCC-Required Information Radio Frequency Interface StatementFCC Output Power Restrictions Exposure to Radio Frequency FieldsRepair and Return Pre-Sales Inquiries and Applications SupportInstallation and Maintenance Support Post-Sale SupportTraining Table of Contents Table of Contents Tracer 4208 System Manual System Description System Overview Features and BenefitsConfiguration and Management OperationalReceiver Sensitivity Antenna Information Receiver PowerLine-of-Site Other ConsiderationsMicrowave Path Engineering Basics Tracer 5045 System Manual Decibels LINE-OF-SITETerminology Calculating the Fade MarginReceiver Power Transmitted Power PT Antenna GainCarrier Wavelength λ Path Distance dSystem Losses L Path Loss LP Typical Coaxial Loss for Common Cable TypesAntenna Alignment Receiver SensitivityAntenna Information Path Loss for Given Path Lengths MilesTracer Rssi Test Points Antenna Beam PatternsFresnel Zones, Earth Curvature, & Antenna Heights Minimum Antenna Height for Given Path Lengths Terrain Terrain Factor Description Other ConsiderationsPath Availability Climate Climate Factor DescriptionMicrowave Path Engineering Basics Tracer 5045 System Manual At-A-Glance Specifications Reviewing the Front Panel DesignReviewing the Front Panel Design Equipment DimensionsPower Requirements Rssi Monitoring InterfaceReviewing the Tracer 5045 Rear Panel Design Rear Panel Description Name Connector RS-232 Connection DB-25 Terminal UseRS-232 Connection Pinout Tracer 5045 DCE to Terminal DTE Diagram DB-25 RS-232 Connection Modem UseTracer 5045 DCE to Personal Computer DB-9 Tracer 5045 DCE to Modem DCE DB-25 Alarm Contacts Plug-In Terminal Block10/100BaseT/TX Connections RJ-48C 100BaseT/Tx Interface PinoutAT-A-GLANCE Specifications DC Power Connection Plug-In Terminal BlockAntenna Interface N-Type connector FuseHardware Description Specification Transmitter Hardware Description Specification Power Engineering Guidelines Tracer 5045 System Manual Network Turnup Procedure Unpack and Inspect the SystemTools Required Contents of Adtran ShipmentIntroduction Unpack and Inspect the SystemChannel Selection Grounding InstructionsSupplying Power to the Unit Connecting the Ethernet InterfacesMounting Options Navigating the Terminal Menu Terminal Menu and System ControlMenu Descriptions Navigating the Terminal Menu Terminal Menu WindowTerminal Menu and System Control Navigating using the Keyboard KeysPassword Protection To do this Press this keyMenu Descriptions Contact InformationRF Status Rx PowerTx Power Ethernet StatusMain Menu Tracer System Configuration Default password for the Tracer 5045 is tracer Tracer Link Performance History Ethernet Switch Status Ethernet Switch Status RX Packets Dropped User Interface Guide Tracer 5045 System Manual Installing/Troubleshooting the Tracer Hardware OverviewTST LED LED Indicators PWR LEDOverview RF Down LEDRF LOW LED RF ErrorsSTEP-BY-STEP Troubleshooting LAN LEDsINSTALLING/TROUBLESHOOTING the Tracer Hardware Installing/Configuring Ethernet Hardware Troubleshooting Guide Tracer 5045 System Manual