Advantech PCI-1784 specifications

Page 18

Step 1: Turn off your computer and unplug the power cord and cables. TURN OFF your computer before installing or removing any components on the computer.

Step 2: Remove the cover of your computer.

Step 3: Remove the slot cover on the back panel of your computer.

Step 4: Touch the metal part on the surface of your computer to neutralize the static electricity that might be on your body.

Step 5: Insert the PCI-1784 card into a PCI slot. Hold the card only by its edges and carefully align it with the slot. Insert the card firmly into place. Use of excessive force must be avoided, otherwise the card might be damaged.

Step 6: Fasten the bracket of the PCI card on the back panel rail of the computer with screws.

Step 7: Connect appropriate accessories (37-pin cable, wiring terminals, etc. if necessary) to the PCI card.

Step 8: Replace the cover of your computer chassis. Re-connect the cables you removed in step 2.

Step 9: Plug in the power cord and turn on the computer.

Note:

In case you installed the card without installing the DLL driver first, Windows 95/98/ME will recognize your card as an “unknown device” after rebooting, and will prompt you to provide the necessary driver. You should ignore the prompting messages (just click the Cancel button) and set up the driver according to the steps described in 2.2 Driver Installation.

After the PCI-1784 card is installed, you can verify whether it is properly installed on your system in the Device Manager:

1.Access the Device Manager through Control Panel/System/Device Manager.

2.The device name of the PCI-1784 should be listed on the Device Manager tab on the System Property Page.

14

Image 18
Contents Page Page Contents Appendix D. Operation Features IntroductionEncoder Interface Flexible Digital Output function CountersDigital Input and Interrupts Special Shielded Cable for Noise ReductionBoard ID Installation Guide ApplicationsInstallation Flow Chart Software Overview Device DriversRegister-level Programming Device Drivers Programming Roadmap Programming ToolsTroubleshooting Device Drivers Error Programming with Device Drivers Function LibraryAccessories Wiring CableWiring Boards Installation UnpackingPage Driver Installation Setup Screen of Advantech Automation SoftwareHardware Installation Select the Individual Drivers optionPage Device name listed on the Device Manager Device Setup & Configuration Board selectionSetting Up and configure the device ‘Setup’ dialog boxOperation dialog box Overview Signal ConnectionsSwitch and Jumper Settings Names of Jumpers Function descriptionBoard ID setting SW1 Signal Connections Connector Signal DescriptionPin Assignment Quadrature encoder input Single ended Outputs EncoderQuadrature encoder up/down counter input connections Isolated digital input Isolated digital outputAppendix A. Specifications TimerEncoder Output Interrupt Counter LatchGeneral Appendix B. Block Diagram ADDRESS, Control and Data BUSPage Appendix C. Register Structure and Format I/O Port Address MapTable C-1 PCI-1784 register format Part + HEX1CH Clock Control Counter 0/1/2/3 mode BASE+00/04/08/0CH Table C-2 PCI-1784 Register for counter 0/1/2/3 modeDI0 Counter 0/1/2/3 latch data BASE+00/04/08/0CH Table C-3 PCI-1784 Register for counter 0/1/2/3 latch dataCounter 0/1/2/3 compare data BASE+10/14/18/1CH Table C-4 PCI-1784 Register for counter 0/1/2/3 compare dataInterrupt control register BASE+20H Table C-5 PCI-1784 Register for interrupt controlInterrupt status register BASE+20H Table C-6 PCI-1784 Register for interrupt statusClear Interrupt BASE+24H Table C-7 PCI-1784 Register for clock controlTable C-8 PCI-1784 Register for clear interrupt Software latch BASE+28H Table C-9 PCI-1784 Register for software latchBoard ID BASE+28H Table C-10 PCI-1784 Board ID dataReset counter BASE+2CH Table C-11 PCI-1784 Register for reset counterDigital output BASE+30H Table C-12 PCI-1784 Register for digital outputDigital input/output BASE+30H Table C-13 PCI-1784 Register for digital input/outputPage Appendix D. Operation Quadrature encoder introductionCounter modes Mode Maximum input rate 8MHz 4MHz 2MHz 1MHzQuadrature input counter mode Single-ended vs. differential inputDisabled mode Pulse modePulse/direction mode Digital noise filterLatch Latch modeClock frequency Maximum width Index latchCounter reset value Timer functionInterrupt function