Asus P5SD2-FM manual IDE connectors 40-1 pin PRIIDE, Secide

Page 35

3.IDE connectors (40-1 pin PRI_IDE, SEC_IDE)

These connectors are for a Ultra DMA 100/66 signal cable. The Ultra DMA 100/ 66 signal cable has three connectors: a blue connector for the primary IDE connector on the motherboard, a black connector for an Ultra DMA 100/66 IDE slave device (optical drive/hard disk drive), and a gray connector for an Ultra DMA 100/66 IDE master device (hard disk drive). If you install two hard disk drives, you must configure the second drive as a slave device by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings.

• Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable.

•Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices.

FM-P5SD2

r

P5SD2-FM IDE Connectors

SEC_IDE

NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1.

IDE_PRI

PIN 1

ASUS P5SD2-FM

1-27

Image 35

Contents Motherboard Copyright 2006 ASUSTeK Computer INC. All Rights Reserved E2471 First Edition MarchContents Bios setup APM Canadian Department of Communications Statement Federal Communications Commission StatementOperation safety Electrical safetyP5SD2-FM specifications summary Internal connectors Support CD contents Form Factor Page Hardware1 information Before you proceed Screw holes Placement directionMotherboard overview P5SD2-FM Motherboard layoutLayout Contents Internal connectors Central Processing Unit CPU Installing the CPURetention tab Load lever PnP cap Asus P5SD2-FM Installing the CPU heatsink and fan Push down two fasteners at a time Uninstalling the CPU heatsink and fan Narrow end of the groove Dimm sockets location Memory ConfigurationsSystem memory Break on the socket Installing a DimmTo install a Dimm Removing a DimmExpansion slots Installing an expansion cardConfiguring an expansion card IRQ assignments for this motherboard Interrupt assignmentsStandard interrupt assignments PCI slots PCI ExpressPCI Express x16 slot Clear RTC RAM Clrtc JumpersBios Recovery 3-pin RECOVERY1 USB device wake-up 3-pin USBPW12, USBPW34, USBPW56, USBPW78 Password Skip LAN port LED indications Connectors Rear panel connectors Port Channel Headset Audio 2, 4, 6, or 8-channel configurationPower LED connector 3-1 pin Pled Internal connectorsFloppy disk drive connector 34-1 pin Floppy IDE connectors 40-1 pin PRIIDE, Secide SATA4 Serial ATA Master/Slave connectorsSpeaker out connector 4-pin Speaker Digital audio connector 3 pin SPDIFO2 USB connectors 10-1 pin USB56, USB78CPU ATX power connectors 24-pin EATXPWR, 4-pin ATX12VFront panel audio connector 10-1 pin Fpaudio Internal audio connector 4-pin AUXReset button Blue 2-pin Reset System panel connector 10-1 pin FpanelSystem power LED Green 2-pin Pled Power/Soft-off button Black 2-pin PwrswHardware information Bios setup Bios setup program Navigation keys Bios menu screenMenu bar Pop-up window Configuration fieldsMenu items Sub-menu itemsSystem Date Day xx/xx/xxxx Legacy Diskette a DisabledMain menu System TimeBlock Multi-sector Transfer Auto LBA/Large Mode AutoPrimary, Secondary, Third, and Fourth IDE Master/Slave Type Auto32Bit Data Transfer Enabled Sata Mode Selection 4PIDE+4SIDEPIO Mode Auto DMA Mode AutoSystem Memory System InformationProcessor Advanced menu CPU Configuration CPU Internal Thermal Control Auto Auto Detect CPU Frequency EnabledChipset Primary Graphics Adapter PCI Express NorthBridge SIS649 Chipset ConfigurationOnboard SiS966 LAN Device Enabled SouthBridge SiS966 Chipset ConfigurationSerial Port1 Address 3F8/IRQ4 Onboard 1394 Controller EnabledPlug and Play O/S No PCI PnPClear Nvram No DMA Channel x PCI Device Allocate IRQ to PCI VGA YesOffBoard PCI/ISA IDE Card Auto IRQ-xx assigned to PCI DeviceUSB Configuration Power menu Power On By PCI Devices Disabled APM ConfigurationPower Button Mode Off/On AC Power Loss Restart Previous StateHardware Monitor Power On By RTC Alarm DisabledMB Temperature xxxoC/xxxoF CPU Temperature xxxoC/xxxoF Smart Q-Fan Function Enabled1st ~ xxth Boot Device xxx Drive Boot menuBoot Device Priority Boot Settings Configuration Security Change Supervisor PasswordChange User Password User Access Level Full AccessExit menu Clear User PasswordPassword Check Setup Discard Changes Load Setup DefaultsExit & Save Changes Exit & Discard Changes