Asus P5SD2-FM manual Speaker out connector 4-pin Speaker

Page 37

5.CPU and Chassis fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN)

The fan connectors support cooling fans of 350 mA ~ 2000 mA (24 W max.) or a total of 1 A ~ 3.48 A (41.76 W max.) at +12 V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector.

Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! DO NOT place jumper caps on the fan connectors.

P5SD2-FM

CHA_FAN

Rotation

+12V

GND

CPU_FAN

CPU FAN PWM CPU FAN IN CPU FAN PWR GND

r

P5SD2-FM Fan Connectors

6.Speaker out connector (4-pin SPEAKER)

This connector is for the case-mounted speaker and allows you to hear system beeps and warnings.

P5SD2-FM

r

P5SD2-FM Speaker Out Connector

SPEAKER

1

+5V	GND Speak Out

ASUS P5SD2-FM

1-29

Image 37

Contents Motherboard Copyright 2006 ASUSTeK Computer INC. All Rights Reserved E2471 First Edition MarchContents Bios setup APM Canadian Department of Communications Statement Federal Communications Commission StatementOperation safety Electrical safetyP5SD2-FM specifications summary Internal connectors Support CD contents Form Factor Page Hardware1 information Before you proceed Motherboard overview Placement directionScrew holes P5SD2-FM Motherboard layoutLayout Contents Internal connectors Central Processing Unit CPU Installing the CPURetention tab Load lever PnP cap Asus P5SD2-FM Installing the CPU heatsink and fan Push down two fasteners at a time Uninstalling the CPU heatsink and fan Narrow end of the groove System memory Memory ConfigurationsDimm sockets location To install a Dimm Installing a DimmRemoving a Dimm Break on the socketConfiguring an expansion card Installing an expansion cardExpansion slots Standard interrupt assignments Interrupt assignmentsIRQ assignments for this motherboard PCI Express x16 slot PCI ExpressPCI slots Clear RTC RAM Clrtc JumpersBios Recovery 3-pin RECOVERY1 USB device wake-up 3-pin USBPW12, USBPW34, USBPW56, USBPW78 Password SkipRear panel connectors ConnectorsLAN port LED indications Port Channel Headset Audio 2, 4, 6, or 8-channel configurationFloppy disk drive connector 34-1 pin Floppy Internal connectorsPower LED connector 3-1 pin Pled IDE connectors 40-1 pin PRIIDE, Secide SATA4 Serial ATA Master/Slave connectorsSpeaker out connector 4-pin Speaker Digital audio connector 3 pin SPDIFO2 USB connectors 10-1 pin USB56, USB78CPU ATX power connectors 24-pin EATXPWR, 4-pin ATX12VFront panel audio connector 10-1 pin Fpaudio Internal audio connector 4-pin AUXSystem power LED Green 2-pin Pled System panel connector 10-1 pin FpanelPower/Soft-off button Black 2-pin Pwrsw Reset button Blue 2-pin ResetHardware information Bios setup Bios setup program Menu bar Bios menu screenNavigation keys Menu items Configuration fieldsSub-menu items Pop-up windowMain menu Legacy Diskette a DisabledSystem Time System Date Day xx/xx/xxxxPrimary, Secondary, Third, and Fourth IDE Master/Slave LBA/Large Mode AutoType Auto Block Multi-sector Transfer AutoPIO Mode Auto Sata Mode Selection 4PIDE+4SIDEDMA Mode Auto 32Bit Data Transfer EnabledProcessor System InformationSystem Memory Advanced menu CPU Configuration Chipset Auto Detect CPU Frequency EnabledCPU Internal Thermal Control Auto Primary Graphics Adapter PCI Express NorthBridge SIS649 Chipset ConfigurationOnboard SiS966 LAN Device Enabled SouthBridge SiS966 Chipset ConfigurationSerial Port1 Address 3F8/IRQ4 Onboard 1394 Controller EnabledClear Nvram No PCI PnPPlug and Play O/S No OffBoard PCI/ISA IDE Card Auto Allocate IRQ to PCI VGA YesIRQ-xx assigned to PCI Device DMA Channel x PCI DeviceUSB Configuration Power menu Power Button Mode Off/On APM ConfigurationAC Power Loss Restart Previous State Power On By PCI Devices DisabledMB Temperature xxxoC/xxxoF CPU Temperature xxxoC/xxxoF Power On By RTC Alarm DisabledSmart Q-Fan Function Enabled Hardware MonitorBoot Device Priority Boot menu1st ~ xxth Boot Device xxx Drive Boot Settings Configuration Security Change Supervisor PasswordChange User Password User Access Level Full AccessPassword Check Setup Clear User PasswordExit menu Exit & Save Changes Load Setup DefaultsExit & Discard Changes Discard Changes