Asus P5SD2-FM manual USB Configuration

Page 59

2.4.5USB Configuration

The items in this menu allow you to change the USB-related features. Select an item then press <Enter> to display the configuration options.

USB Configuration

Module Version - 2.24.0-11.4

USB Devices Enabled: None

OnBoard	SIS USB1.1	DEVICE	[Enabled]
OnBoard	SIS USB2.o	DEVICE	[Enabled]
Legacy USB Support			[Enabled]
USB 2.0	Controller	Mode	[HiSpeed]
BIOS EHCI Hand-off			[Enabled]

The Module Version and USB Devices Enabled items show the auto-detected values. If no USB device is detected, the item shows None.

Onboard SIS USB1.1 DEVICE [Enabled]

Allows you to enable or disable the OnBoard SIS USB1.1 Device. Configuration options: [Disabled] [Enabled]

Onboard SIS USB2.0 DEVICE [Enabled]

Allows you to enable or disable the OnBoard SIS USB1.1 Device. Configuration options: [Disabled] [Enabled]

Legacy USB Support [Enabled]

Allows you to enable or disable support for USB devices on legacy operating systems (OS). Setting to [Auto] allows the system to detect the presence of USB devices at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled. Configuration options: [Disabled] [Enabled] [Auto]

USB 2.0 Controller Mode [HiSpeed]

Allows you to set the USB 2.0 controller mode to HiSpeed (480 Mbps) or FullSpeed (12 Mbps). Configuration options: [FullSpeed] [HiSpeed ]

BIOS EHCI Hand-Off [Enabled]

Allows you to enable or disable the BIOS EHCI Hand-Off..

Configuration options: [Disabled] [Enabled]

ASUS P5SD2-FM

2-17

Image 59

Contents Motherboard Copyright 2006 ASUSTeK Computer INC. All Rights Reserved E2471 First Edition MarchContents Bios setup APM Canadian Department of Communications Statement Federal Communications Commission StatementOperation safety Electrical safetyP5SD2-FM specifications summary Internal connectors Support CD contents Form Factor Page Hardware1 information Before you proceed Screw holes Placement directionMotherboard overview P5SD2-FM Motherboard layoutLayout Contents Internal connectors Central Processing Unit CPU Installing the CPURetention tab Load lever PnP cap Asus P5SD2-FM Installing the CPU heatsink and fan Push down two fasteners at a time Uninstalling the CPU heatsink and fan Narrow end of the groove Dimm sockets location Memory ConfigurationsSystem memory Break on the socket Installing a DimmTo install a Dimm Removing a DimmExpansion slots Installing an expansion cardConfiguring an expansion card IRQ assignments for this motherboard Interrupt assignmentsStandard interrupt assignments PCI slots PCI ExpressPCI Express x16 slot Clear RTC RAM Clrtc JumpersBios Recovery 3-pin RECOVERY1 USB device wake-up 3-pin USBPW12, USBPW34, USBPW56, USBPW78 Password SkipLAN port LED indications ConnectorsRear panel connectors Port Channel Headset Audio 2, 4, 6, or 8-channel configurationPower LED connector 3-1 pin Pled Internal connectorsFloppy disk drive connector 34-1 pin Floppy IDE connectors 40-1 pin PRIIDE, Secide SATA4 Serial ATA Master/Slave connectorsSpeaker out connector 4-pin Speaker Digital audio connector 3 pin SPDIFO2 USB connectors 10-1 pin USB56, USB78CPU ATX power connectors 24-pin EATXPWR, 4-pin ATX12VFront panel audio connector 10-1 pin Fpaudio Internal audio connector 4-pin AUXReset button Blue 2-pin Reset System panel connector 10-1 pin FpanelSystem power LED Green 2-pin Pled Power/Soft-off button Black 2-pin PwrswHardware information Bios setup Bios setup program Navigation keys Bios menu screenMenu bar Pop-up window Configuration fieldsMenu items Sub-menu itemsSystem Date Day xx/xx/xxxx Legacy Diskette a DisabledMain menu System TimeBlock Multi-sector Transfer Auto LBA/Large Mode AutoPrimary, Secondary, Third, and Fourth IDE Master/Slave Type Auto32Bit Data Transfer Enabled Sata Mode Selection 4PIDE+4SIDEPIO Mode Auto DMA Mode AutoSystem Memory System InformationProcessor Advanced menu CPU Configuration CPU Internal Thermal Control Auto Auto Detect CPU Frequency EnabledChipset Primary Graphics Adapter PCI Express NorthBridge SIS649 Chipset ConfigurationOnboard SiS966 LAN Device Enabled SouthBridge SiS966 Chipset ConfigurationSerial Port1 Address 3F8/IRQ4 Onboard 1394 Controller EnabledPlug and Play O/S No PCI PnPClear Nvram No DMA Channel x PCI Device Allocate IRQ to PCI VGA YesOffBoard PCI/ISA IDE Card Auto IRQ-xx assigned to PCI DeviceUSB Configuration Power menu Power On By PCI Devices Disabled APM ConfigurationPower Button Mode Off/On AC Power Loss Restart Previous StateHardware Monitor Power On By RTC Alarm DisabledMB Temperature xxxoC/xxxoF CPU Temperature xxxoC/xxxoF Smart Q-Fan Function Enabled1st ~ xxth Boot Device xxx Drive Boot menuBoot Device Priority Boot Settings Configuration Security Change Supervisor PasswordChange User Password User Access Level Full AccessExit menu Clear User PasswordPassword Check Setup Discard Changes Load Setup DefaultsExit & Save Changes Exit & Discard Changes