Asus P5SD2-FM manual Boot Settings Configuration

Page 64

2.6.2Boot Settings Configuration

Boot Settings Configuration

 

Allows BIOS to skip

Quick Boot

[Enabled]

certain tests while

booting. This will

Full Screen Logo

[Enabled]

decrease the time

Bootup Num-Lock

[On]

needed to boot the

Wait For F If Error

[Disabled]

system.

Hit DEL Message Display

[Enabled]

 

Interrupt 19 Capture

[Disabled]

 

Quick Boot [Enabled]

Enabling this item allows the BIOS to skip some power on self tests (POST) while booting to decrease the time needed to boot the system. When set to [Disabled], BIOS performs all the POST items.

Configuration options: [Disabled] [Enabled]

Full Screen Logo [Enabled]

This allows you to enable or disable the full screen logo display feature. Configuration options: [Disabled] [Enabled]

Set this item to [Enabled] to use the ASUS MyLogo™ feature.

Bootup Num-Lock [On]

Allows you to select the power-on state for the NumLock.

Configuration options: [Off] [On]

Wait for ‘ F1’If Error [Disabled]

When set to Enabled, the system waits for the F1 key to be pressed when error occurs. Configuration options: [Disabled] [Enabled]

Hit ‘DEL’Message Display [Enabled]

When set to Enabled, the system displays the message “Press DEL to run Setup ” during POST. Configuration options: [Disabled] [Enabled]

Interrupt 19 Capture [Disabled]

When set to [Enabled], this function allows the option ROMs to trap Interrupt 19. Configuration options: [Disabled] [Enabled]

2-22

Chapter 2: BIOS setup

Image 64
Contents Motherboard E2471 First Edition March Copyright 2006 ASUSTeK Computer INC. All Rights ReservedContents Bios setup APM Federal Communications Commission Statement Canadian Department of Communications StatementElectrical safety Operation safetyP5SD2-FM specifications summary Internal connectors Support CD contents Form Factor Page Hardware1 information Before you proceed Motherboard overview Placement directionScrew holes Motherboard layout P5SD2-FMLayout Contents Internal connectors Installing the CPU Central Processing Unit CPURetention tab Load lever PnP cap Asus P5SD2-FM Installing the CPU heatsink and fan Push down two fasteners at a time Uninstalling the CPU heatsink and fan Narrow end of the groove System memory Memory ConfigurationsDimm sockets location Installing a Dimm To install a DimmRemoving a Dimm Break on the socketConfiguring an expansion card Installing an expansion cardExpansion slots Standard interrupt assignments Interrupt assignmentsIRQ assignments for this motherboard PCI Express x16 slot PCI ExpressPCI slots Jumpers Clear RTC RAM ClrtcBios Recovery 3-pin RECOVERY1 Password Skip USB device wake-up 3-pin USBPW12, USBPW34, USBPW56, USBPW78Rear panel connectors ConnectorsLAN port LED indications Audio 2, 4, 6, or 8-channel configuration Port Channel HeadsetFloppy disk drive connector 34-1 pin Floppy Internal connectorsPower LED connector 3-1 pin Pled IDE connectors 40-1 pin PRIIDE, Secide Serial ATA Master/Slave connectors SATA4Speaker out connector 4-pin Speaker USB connectors 10-1 pin USB56, USB78 Digital audio connector 3 pin SPDIFO2ATX power connectors 24-pin EATXPWR, 4-pin ATX12V CPUInternal audio connector 4-pin AUX Front panel audio connector 10-1 pin FpaudioSystem panel connector 10-1 pin Fpanel System power LED Green 2-pin PledPower/Soft-off button Black 2-pin Pwrsw Reset button Blue 2-pin ResetHardware information Bios setup Bios setup program Menu bar Bios menu screenNavigation keys Configuration fields Menu itemsSub-menu items Pop-up windowLegacy Diskette a Disabled Main menuSystem Time System Date Day xx/xx/xxxxLBA/Large Mode Auto Primary, Secondary, Third, and Fourth IDE Master/SlaveType Auto Block Multi-sector Transfer AutoSata Mode Selection 4PIDE+4SIDE PIO Mode AutoDMA Mode Auto 32Bit Data Transfer EnabledProcessor System InformationSystem Memory Advanced menu CPU Configuration Chipset Auto Detect CPU Frequency EnabledCPU Internal Thermal Control Auto NorthBridge SIS649 Chipset Configuration Primary Graphics Adapter PCI ExpressSouthBridge SiS966 Chipset Configuration Onboard SiS966 LAN Device EnabledOnboard 1394 Controller Enabled Serial Port1 Address 3F8/IRQ4Clear Nvram No PCI PnPPlug and Play O/S No Allocate IRQ to PCI VGA Yes OffBoard PCI/ISA IDE Card AutoIRQ-xx assigned to PCI Device DMA Channel x PCI DeviceUSB Configuration Power menu APM Configuration Power Button Mode Off/OnAC Power Loss Restart Previous State Power On By PCI Devices DisabledPower On By RTC Alarm Disabled MB Temperature xxxoC/xxxoF CPU Temperature xxxoC/xxxoFSmart Q-Fan Function Enabled Hardware MonitorBoot Device Priority Boot menu1st ~ xxth Boot Device xxx Drive Boot Settings Configuration Change Supervisor Password SecurityUser Access Level Full Access Change User PasswordPassword Check Setup Clear User PasswordExit menu Load Setup Defaults Exit & Save ChangesExit & Discard Changes Discard Changes