Asus P5SD2-FM manual USB connectors 10-1 pin USB56, USB78, Digital audio connector 3 pin SPDIFO2

Page 38

7.USB connectors (10-1 pin USB56, USB78)

These connectors are for USB 2.0 ports. Connect the USB/GAME module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specification that supports up to 480 Mbps connection speed.

P5SD2-FM

r

P5SD2-FM USB 2.0 Connectors

NC

GND

USB_P6+

USB_P6-

USB+5V

USB56

GND

USB_P5+

USB_P5-

USB+5V

NC

GND

USB_P8+

USB_P8-

USB+5V

USB78

GND

USB_P7+

USB_P7-

USB+5V

Never connect a 1394 cable to the USB connectors. Doing so will damage the motherboard!

8.Digital audio connector (3 pin SPDIF_O2)

This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port. Connect the S/PDIF module cable to this connector, then install the module to a slot opening at the back of the system chassis.

The S/PDIF module is purchased separately.

P5SD2-FM

r

SPDIF_O2

GND

SIG +5V

P5SD2-FM Digital Audio Connector

1-30	Chapter 1: Hardware information

Image 38

Contents Motherboard E2471 First Edition March Copyright 2006 ASUSTeK Computer INC. All Rights ReservedContents Bios setup APM Federal Communications Commission Statement Canadian Department of Communications StatementElectrical safety Operation safetyP5SD2-FM specifications summary Internal connectors Support CD contents Form Factor Page Hardware1 information Before you proceed Screw holes Placement directionMotherboard overview Motherboard layout P5SD2-FMLayout Contents Internal connectors Installing the CPU Central Processing Unit CPURetention tab Load lever PnP cap Asus P5SD2-FM Installing the CPU heatsink and fan Push down two fasteners at a time Uninstalling the CPU heatsink and fan Narrow end of the groove Dimm sockets location Memory ConfigurationsSystem memory Removing a Dimm Installing a DimmTo install a Dimm Break on the socketExpansion slots Installing an expansion cardConfiguring an expansion card IRQ assignments for this motherboard Interrupt assignmentsStandard interrupt assignments PCI slots PCI ExpressPCI Express x16 slot Jumpers Clear RTC RAM ClrtcBios Recovery 3-pin RECOVERY1 Password Skip USB device wake-up 3-pin USBPW12, USBPW34, USBPW56, USBPW78LAN port LED indications ConnectorsRear panel connectors Audio 2, 4, 6, or 8-channel configuration Port Channel HeadsetPower LED connector 3-1 pin Pled Internal connectorsFloppy disk drive connector 34-1 pin Floppy IDE connectors 40-1 pin PRIIDE, Secide Serial ATA Master/Slave connectors SATA4Speaker out connector 4-pin Speaker USB connectors 10-1 pin USB56, USB78 Digital audio connector 3 pin SPDIFO2ATX power connectors 24-pin EATXPWR, 4-pin ATX12V CPUInternal audio connector 4-pin AUX Front panel audio connector 10-1 pin FpaudioPower/Soft-off button Black 2-pin Pwrsw System panel connector 10-1 pin FpanelSystem power LED Green 2-pin Pled Reset button Blue 2-pin ResetHardware information Bios setup Bios setup program Navigation keys Bios menu screenMenu bar Sub-menu items Configuration fieldsMenu items Pop-up windowSystem Time Legacy Diskette a DisabledMain menu System Date Day xx/xx/xxxxType Auto LBA/Large Mode AutoPrimary, Secondary, Third, and Fourth IDE Master/Slave Block Multi-sector Transfer AutoDMA Mode Auto Sata Mode Selection 4PIDE+4SIDEPIO Mode Auto 32Bit Data Transfer EnabledSystem Memory System InformationProcessor Advanced menu CPU Configuration CPU Internal Thermal Control Auto Auto Detect CPU Frequency EnabledChipset NorthBridge SIS649 Chipset Configuration Primary Graphics Adapter PCI ExpressSouthBridge SiS966 Chipset Configuration Onboard SiS966 LAN Device EnabledOnboard 1394 Controller Enabled Serial Port1 Address 3F8/IRQ4Plug and Play O/S No PCI PnPClear Nvram No IRQ-xx assigned to PCI Device Allocate IRQ to PCI VGA YesOffBoard PCI/ISA IDE Card Auto DMA Channel x PCI DeviceUSB Configuration Power menu AC Power Loss Restart Previous State APM ConfigurationPower Button Mode Off/On Power On By PCI Devices DisabledSmart Q-Fan Function Enabled Power On By RTC Alarm DisabledMB Temperature xxxoC/xxxoF CPU Temperature xxxoC/xxxoF Hardware Monitor1st ~ xxth Boot Device xxx Drive Boot menuBoot Device Priority Boot Settings Configuration Change Supervisor Password SecurityUser Access Level Full Access Change User PasswordExit menu Clear User PasswordPassword Check Setup Exit & Discard Changes Load Setup DefaultsExit & Save Changes Discard Changes