Asus P5SD2-FM manual Chipset, CPU Internal Thermal Control Auto, Auto Detect CPU Frequency Enabled

Page 53

CPU Internal Thermal Control [Auto]

Disables or sets the CPU internal thermal control.

Configuration options: [Auto] [Disabled]

Scroll down the screen to display the following items.

Auto Detect CPU Frequency [Enabled]

Enableds or disables the Auto Detect CPU Frequency feature. Configuration options: [Disabled] [Enabled]

CPU Frequency Setting [200]

Allows you to set the CPU Frequency.

Configuration options: [100] ~ [355]

2.4.2Chipset

The Chipset menu allows you to change the advanced chipset settings. Select an item then press <Enter> to display the sub-menu.

NorthBridge

SIS649 Configuration

Options for NB

SouthBridge

SiS965/SiS965L Configuration

 

ASUS P5SD2-FM

2-11

Image 53
Contents Motherboard Copyright 2006 ASUSTeK Computer INC. All Rights Reserved E2471 First Edition MarchContents Bios setup APM Canadian Department of Communications Statement Federal Communications Commission StatementOperation safety Electrical safetyP5SD2-FM specifications summary Internal connectors Support CD contents Form Factor Page Hardware1 information Before you proceed Screw holes Placement directionMotherboard overview P5SD2-FM Motherboard layoutLayout Contents Internal connectors Central Processing Unit CPU Installing the CPURetention tab Load lever PnP cap Asus P5SD2-FM Installing the CPU heatsink and fan Push down two fasteners at a time Uninstalling the CPU heatsink and fan Narrow end of the groove Dimm sockets location Memory ConfigurationsSystem memory To install a Dimm Installing a DimmRemoving a Dimm Break on the socketExpansion slots Installing an expansion cardConfiguring an expansion card IRQ assignments for this motherboard Interrupt assignmentsStandard interrupt assignments PCI slots PCI ExpressPCI Express x16 slot Clear RTC RAM Clrtc JumpersBios Recovery 3-pin RECOVERY1 USB device wake-up 3-pin USBPW12, USBPW34, USBPW56, USBPW78 Password SkipLAN port LED indications ConnectorsRear panel connectors Port Channel Headset Audio 2, 4, 6, or 8-channel configurationPower LED connector 3-1 pin Pled Internal connectorsFloppy disk drive connector 34-1 pin Floppy IDE connectors 40-1 pin PRIIDE, Secide SATA4 Serial ATA Master/Slave connectorsSpeaker out connector 4-pin Speaker Digital audio connector 3 pin SPDIFO2 USB connectors 10-1 pin USB56, USB78CPU ATX power connectors 24-pin EATXPWR, 4-pin ATX12VFront panel audio connector 10-1 pin Fpaudio Internal audio connector 4-pin AUXSystem power LED Green 2-pin Pled System panel connector 10-1 pin FpanelPower/Soft-off button Black 2-pin Pwrsw Reset button Blue 2-pin ResetHardware information Bios setup Bios setup program Navigation keys Bios menu screenMenu bar Menu items Configuration fieldsSub-menu items Pop-up windowMain menu Legacy Diskette a DisabledSystem Time System Date Day xx/xx/xxxxPrimary, Secondary, Third, and Fourth IDE Master/Slave LBA/Large Mode AutoType Auto Block Multi-sector Transfer AutoPIO Mode Auto Sata Mode Selection 4PIDE+4SIDEDMA Mode Auto 32Bit Data Transfer EnabledSystem Memory System InformationProcessor Advanced menu CPU Configuration CPU Internal Thermal Control Auto Auto Detect CPU Frequency EnabledChipset Primary Graphics Adapter PCI Express NorthBridge SIS649 Chipset ConfigurationOnboard SiS966 LAN Device Enabled SouthBridge SiS966 Chipset ConfigurationSerial Port1 Address 3F8/IRQ4 Onboard 1394 Controller EnabledPlug and Play O/S No PCI PnPClear Nvram No OffBoard PCI/ISA IDE Card Auto Allocate IRQ to PCI VGA YesIRQ-xx assigned to PCI Device DMA Channel x PCI DeviceUSB Configuration Power menu Power Button Mode Off/On APM ConfigurationAC Power Loss Restart Previous State Power On By PCI Devices DisabledMB Temperature xxxoC/xxxoF CPU Temperature xxxoC/xxxoF Power On By RTC Alarm DisabledSmart Q-Fan Function Enabled Hardware Monitor1st ~ xxth Boot Device xxx Drive Boot menuBoot Device Priority Boot Settings Configuration Security Change Supervisor PasswordChange User Password User Access Level Full AccessExit menu Clear User PasswordPassword Check Setup Exit & Save Changes Load Setup DefaultsExit & Discard Changes Discard Changes