Asus P5SD2-FM manual Serial Port1 Address 3F8/IRQ4, Onboard 1394 Controller Enabled

Page 56

2.4.3Onboard Devices Configuration

Configure ITE8712 Super IO Chipset

Serial Port1	Address	[3F8/IRQ4]
Serial Port1 Mode		[Normal]
Onboard 1394	Controller	[Enabled]

Allows BIOS to enable or disable the floppy controller.

Serial Port1 Address [3F8/IRQ4]

Allows you to select the Serial Port1 base address.

Configuration options: [Disabled] [3F8/IRQ4] [3E8/IRQ4] [2E8/IRQ3]

Serial Port1 Mode [Normal]

Allows you to select the Serial Port1 mode.

Configuration options: [Normal] [IrDA] [ASK IR]

COMA Duplex Mode [Half Duplex]

Allows the BIOS to select Full or Half Duplex for Serial Port. This appears only when the Serial Port1 Mode item is set to [IrDA] or [ASK IR] Configuration options: [Full Duplex] [Half Duplex]

Onboard 1394 Controller [Enabled]

Allows you to enable or disable the onboard IEEE 1394a controller. Configuration options: [Disabled] [Enabled]

2-14	Chapter 2: BIOS setup

Image 56

Contents Motherboard E2471 First Edition March Copyright 2006 ASUSTeK Computer INC. All Rights ReservedContents Bios setup APM Federal Communications Commission Statement Canadian Department of Communications StatementElectrical safety Operation safetyP5SD2-FM specifications summary Internal connectors Support CD contents Form Factor Page Hardware1 information Before you proceed Screw holes Placement directionMotherboard overview Motherboard layout P5SD2-FMLayout Contents Internal connectors Installing the CPU Central Processing Unit CPURetention tab Load lever PnP cap Asus P5SD2-FM Installing the CPU heatsink and fan Push down two fasteners at a time Uninstalling the CPU heatsink and fan Narrow end of the groove Dimm sockets location Memory ConfigurationsSystem memory Installing a Dimm To install a DimmRemoving a Dimm Break on the socketExpansion slots Installing an expansion cardConfiguring an expansion card IRQ assignments for this motherboard Interrupt assignmentsStandard interrupt assignments PCI slots PCI ExpressPCI Express x16 slot Jumpers Clear RTC RAM ClrtcBios Recovery 3-pin RECOVERY1 Password Skip USB device wake-up 3-pin USBPW12, USBPW34, USBPW56, USBPW78LAN port LED indications ConnectorsRear panel connectors Audio 2, 4, 6, or 8-channel configuration Port Channel HeadsetPower LED connector 3-1 pin Pled Internal connectorsFloppy disk drive connector 34-1 pin Floppy IDE connectors 40-1 pin PRIIDE, Secide Serial ATA Master/Slave connectors SATA4Speaker out connector 4-pin Speaker USB connectors 10-1 pin USB56, USB78 Digital audio connector 3 pin SPDIFO2ATX power connectors 24-pin EATXPWR, 4-pin ATX12V CPUInternal audio connector 4-pin AUX Front panel audio connector 10-1 pin FpaudioSystem panel connector 10-1 pin Fpanel System power LED Green 2-pin PledPower/Soft-off button Black 2-pin Pwrsw Reset button Blue 2-pin ResetHardware information Bios setup Bios setup program Navigation keys Bios menu screenMenu bar Configuration fields Menu itemsSub-menu items Pop-up windowLegacy Diskette a Disabled Main menuSystem Time System Date Day xx/xx/xxxxLBA/Large Mode Auto Primary, Secondary, Third, and Fourth IDE Master/SlaveType Auto Block Multi-sector Transfer AutoSata Mode Selection 4PIDE+4SIDE PIO Mode AutoDMA Mode Auto 32Bit Data Transfer EnabledSystem Memory System InformationProcessor Advanced menu CPU Configuration CPU Internal Thermal Control Auto Auto Detect CPU Frequency EnabledChipset NorthBridge SIS649 Chipset Configuration Primary Graphics Adapter PCI ExpressSouthBridge SiS966 Chipset Configuration Onboard SiS966 LAN Device EnabledOnboard 1394 Controller Enabled Serial Port1 Address 3F8/IRQ4Plug and Play O/S No PCI PnPClear Nvram No Allocate IRQ to PCI VGA Yes OffBoard PCI/ISA IDE Card AutoIRQ-xx assigned to PCI Device DMA Channel x PCI DeviceUSB Configuration Power menu APM Configuration Power Button Mode Off/OnAC Power Loss Restart Previous State Power On By PCI Devices DisabledPower On By RTC Alarm Disabled MB Temperature xxxoC/xxxoF CPU Temperature xxxoC/xxxoFSmart Q-Fan Function Enabled Hardware Monitor1st ~ xxth Boot Device xxx Drive Boot menuBoot Device Priority Boot Settings Configuration Change Supervisor Password SecurityUser Access Level Full Access Change User PasswordExit menu Clear User PasswordPassword Check Setup Load Setup Defaults Exit & Save ChangesExit & Discard Changes Discard Changes