Asus P5SD2-FM manual Boot menu, Boot Device Priority, 1st ~ xxth Boot Device xxx Drive

Page 63

2.6Boot menu

The Boot menu items allow you to change the system boot options. Select an item then press <Enter> to display the sub-menu.

Boot Settings		Specifies	the Boot
Boot	Device Priority	Device Boot Priority
		sequence.
Boot	Settings Configuration
Security

2.6.1Boot Device Priority

Boot Device Priority

1st Boot Device 2nd Boot Device 3nd Boot Device

[1st Floppy Drive] [PM-ST320410A] [PS-ASUS CD-S520/A]

1st ~ xxth Boot Device [xxx Drive]

These items specify the boot device priority sequence from the available devices. The number of device items that appears on the screen depends on the number of devices installed in the system.

Configuration options: [Disabled] [xxx Drive]

ASUS P5SD2-FM

2-21

Image 63

Contents Motherboard Copyright 2006 ASUSTeK Computer INC. All Rights Reserved E2471 First Edition MarchContents Bios setup APM Canadian Department of Communications Statement Federal Communications Commission StatementOperation safety Electrical safetyP5SD2-FM specifications summary Internal connectors Support CD contents Form Factor Page Hardware1 information Before you proceed Placement direction Motherboard overviewScrew holes P5SD2-FM Motherboard layoutLayout Contents Internal connectors Central Processing Unit CPU Installing the CPURetention tab Load lever PnP cap Asus P5SD2-FM Installing the CPU heatsink and fan Push down two fasteners at a time Uninstalling the CPU heatsink and fan Narrow end of the groove Memory Configurations System memoryDimm sockets location Break on the socket Installing a DimmTo install a Dimm Removing a DimmInstalling an expansion card Configuring an expansion cardExpansion slots Interrupt assignments Standard interrupt assignmentsIRQ assignments for this motherboard PCI Express PCI Express x16 slotPCI slots Clear RTC RAM Clrtc JumpersBios Recovery 3-pin RECOVERY1 USB device wake-up 3-pin USBPW12, USBPW34, USBPW56, USBPW78 Password SkipConnectors Rear panel connectorsLAN port LED indications Port Channel Headset Audio 2, 4, 6, or 8-channel configurationInternal connectors Floppy disk drive connector 34-1 pin FloppyPower LED connector 3-1 pin Pled IDE connectors 40-1 pin PRIIDE, Secide SATA4 Serial ATA Master/Slave connectorsSpeaker out connector 4-pin Speaker Digital audio connector 3 pin SPDIFO2 USB connectors 10-1 pin USB56, USB78CPU ATX power connectors 24-pin EATXPWR, 4-pin ATX12VFront panel audio connector 10-1 pin Fpaudio Internal audio connector 4-pin AUXReset button Blue 2-pin Reset System panel connector 10-1 pin FpanelSystem power LED Green 2-pin Pled Power/Soft-off button Black 2-pin PwrswHardware information Bios setup Bios setup program Bios menu screen Menu barNavigation keys Pop-up window Configuration fieldsMenu items Sub-menu itemsSystem Date Day xx/xx/xxxx Legacy Diskette a DisabledMain menu System TimeBlock Multi-sector Transfer Auto LBA/Large Mode AutoPrimary, Secondary, Third, and Fourth IDE Master/Slave Type Auto32Bit Data Transfer Enabled Sata Mode Selection 4PIDE+4SIDEPIO Mode Auto DMA Mode AutoSystem Information ProcessorSystem Memory Advanced menu CPU Configuration Auto Detect CPU Frequency Enabled ChipsetCPU Internal Thermal Control Auto Primary Graphics Adapter PCI Express NorthBridge SIS649 Chipset ConfigurationOnboard SiS966 LAN Device Enabled SouthBridge SiS966 Chipset ConfigurationSerial Port1 Address 3F8/IRQ4 Onboard 1394 Controller EnabledPCI PnP Clear Nvram NoPlug and Play O/S No DMA Channel x PCI Device Allocate IRQ to PCI VGA YesOffBoard PCI/ISA IDE Card Auto IRQ-xx assigned to PCI DeviceUSB Configuration Power menu Power On By PCI Devices Disabled APM ConfigurationPower Button Mode Off/On AC Power Loss Restart Previous StateHardware Monitor Power On By RTC Alarm DisabledMB Temperature xxxoC/xxxoF CPU Temperature xxxoC/xxxoF Smart Q-Fan Function EnabledBoot menu Boot Device Priority1st ~ xxth Boot Device xxx Drive Boot Settings Configuration Security Change Supervisor PasswordChange User Password User Access Level Full AccessClear User Password Password Check SetupExit menu Discard Changes Load Setup DefaultsExit & Save Changes Exit & Discard Changes