Asus VIA K8T800, VIA VT8237, K8V-F manual ATX power connectors 20-pin ATXPOWER1, 4-pin ATX12V

Page 31

7.ATX power connectors (20-pin ATX_POWER1, 4-pin ATX12V)

These connectors connect to an ATX 12V power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit.

In addition to the 20-pin ATXPWR1 connector, this motherboard requires that you connect the 4-pin ATX +12V power plug to provide sufficient power to the CPU.

• Do not forget to connect the 4-pin ATX +12V power plug. Otherwise, the system does not boot up.

•Make sure that your ATX 12V power supply can provide 12A on the +12V lead and at least 1A on the +5-volt standby lead (+5VSB). The minimum recommended wattage is 300W, or 350W for a fully configured system. The system may become unstable or may not boot up if the power is inadequate.

ATXPWRATX12V

Pin 1

+5.0VDC

+5.0VDC

-5.0VDC

COM

COM

COM

PS_ON#

COM

-12.0VDC +3.3VDC

K8V-F ATX Power Connectors

8.Front panel audio connector (10-1 pin FP_AUDIO)

This is an interface for the Intel front panel audio cable that allow convenient connection and control of audio devices.

K8V-F

FP_AUDIO

BLINE_OUT_L Line out_L

NC

BLINE_OUT_R	Line out_R
+5VA	MICPWR
AGND	MIC2

K8V-F Front Panel Audio Connector

ASUS K8V-F motherboard user guide

1-21

Image 31

Contents Motherboard E1495 First Edition December Contents Chapter Bios informationContents Federal Communications Commission Statement Electrical safety SafetyinformationOperation safety Aboutthisguide Where to find more informationConventions used in this guide CPU K8V-FspecificationsummaryBios features Industry standard Manageability Form Factor Chapter Welcome Special featuresHardware information AGP 8X support Channel and digital audio solutionAsus EZ Flash Bios Integrated 10/100 Mbps LANBefore you proceed Onboard LEDMotherboard layout Motherboard overviewScrew holes Placement directionCentral Processing Unit CPU Installing the CPUAngle System memory Memory configuratinsOverview Removing a Dimm Installing a DimmConfiguring an expansion card Installing an expansion cardExpansion slots IRQ assignments for this motherboard Standard interrupt assignmentsAGP slot PCI slotsJumpers Keyboard power 3-pin KBPWR1Clear RTC RAM CLRTC1 K8V-F Keyboard Power Setting Rear panel connectors ConnectorsBios Recovery procedure Internal connectors Auxilliary connector 4-pin AUX Important notes on Serial ATA Serial ATA connectors 7-pin SATA1, SATA2Ieee 1394 connector 10-1 pin IE13941 CPU and Chassis Fan Connectors 3-pin CPUFAN1, CHAFAN1Front panel audio connector 10-1 pin Fpaudio ATX power connectors 20-pin ATXPOWER1, 4-pin ATX12VUSB headers 10-1 pin USB56, USB78 Reset Switch Lead 2-pin Reset System panel connector 20-pin PANEL1System Power LED Lead 3-1 pin Pled ATX Power Switch / Soft-Off Switch Lead 2-pin PwrswProduct Introduction Bios information Creating a bootable floppy disk Managing and updating your BiosUsing Afudos to update the Bios Using Afudos to copy the current BiosAfudos /ifilename.rom To update the Bios using Asus EZ Flash Using Asus EZ Flash to update the BiosBIOSSetupprogram Bios menu screen Menu items Legacy Diskette a 1.44M, 3.5 MainmenuSystem Time System Date Day xx/xx/xxxxPrimary/Secondary IDE Master/Slave Smart Monitoring Auto 32Bit Data Transfer DisabledAcoustic Management Disabled System InformationAdvancedmenu CPU ConfigurationHT Data Width Upstream 16 BIT HT Tristate Enable DisabledCRC Flood Enable Disabled HT Frequency 800 MHzMemclock Mode Auto Memory ConfigurationBank Interleaving Auto CAS Latency CL Auto Data Cache BG Scrub Disabled L2 Cache BG Scrub DisabledChipset Cool N’ Quiet EnabledSearch for MDA Resources No AGP Mode AGPAGP Fast Write Enabled Primary Graphics Adapter AGPMPS Revision PCI Delay Transaction DisabledLegacy USB Support Auto USB 1.1 Ports Configuration USB 8 PortsUSB 2.0 Controller Enabled USB 2.0 Controller Mode HiSpeedOnboard Devices Configuration Parallel Port IRQ IRQ7 Parallel Port Mode NormalPCIPnP Powermenu APM Configuration Power On External Modems Disabled Video Power Down Mode SuspendHard Disk Power Down Mode Enabled Power On By RTC Alarm DisabledHardware Monitor CPU Temperature xxxC/xxxF MB Temperature xxxC/xxxFVcore Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage Boot Device Priority Boot menu1st ~ xxth Boot Device 1st Floppy Drive Boot Settings Configuration Change Supervisor Password Interrupt 19 Capture DisabledSecurity Password Check Setup User Access Level Full AccessChange User Password Clear User PasswordExit & Discard Changes Load Setup DefaultsExitmenu Exit & Save Changes