Asus VIA K8T800, VIA VT8237, K8V-F manual CAS Latency CL Auto

Page 49

CAS Latency (CL) [Auto]

This item sets the CAS Latency. Configuration options: [Auto] [2.0] [3.0] [2.5]

TRCD [Auto]

This item sets the TRCD. Configuration options: [Auto] [2 CLK] [3 CLK] [4 CLK] [5 CLK] [6 CLK]

TRAS [Auto]

This item sets the TRAS. Configuration options: [Auto] [5 CLK] [6 CLK] [7 CLK] [8 CLK] [9 CLK] [10 CLK] [11 CLK] [12 CLK] [13 CLK] [14 CLK] [15 CLK]

TRP [Auto]

This item sets the TRP. Configuration options: [Auto] [2 CLK] [3 CLK] [4 CLK] [5 CLK] [6 CLK]

ECC Configuration

ECC Configuration

 

Master ECC Enable

Master ECC Enable

[Disabled]

supports on all nodes for

ECC error detect and

 

 

correction.

Master ECC Enable [Disabled]

This item enables or disables support on all nodes for ECC error detect and correction. Configuration options: [Disabled] [Enabled]

The following items appear only when the Master ECC Enable item is enabled.

DRAM ECC Enable [Disabled]

This item enables or disables the DRAM ECC that allows hardware to automatically report and correct memory errors and maintain system integrity. Configuration options: [Disabled] [Enabled]

ASUS K8V-F motherboard user guide

2-15

Image 49
Contents Motherboard E1495 First Edition December Contents Chapter Bios informationContents Federal Communications Commission Statement Electrical safety SafetyinformationOperation safety Aboutthisguide Where to find more informationConventions used in this guide CPU K8V-FspecificationsummaryBios features Industry standard Manageability Form Factor Chapter Welcome Special featuresAsus EZ Flash Bios Channel and digital audio solutionIntegrated 10/100 Mbps LAN Hardware information AGP 8X supportBefore you proceed Onboard LEDMotherboard layout Motherboard overviewScrew holes Placement directionCentral Processing Unit CPU Installing the CPUAngle System memory Memory configuratinsOverview Removing a Dimm Installing a DimmConfiguring an expansion card Installing an expansion cardExpansion slots IRQ assignments for this motherboard Standard interrupt assignmentsAGP slot PCI slotsJumpers Keyboard power 3-pin KBPWR1Clear RTC RAM CLRTC1 K8V-F Keyboard Power Setting Rear panel connectors ConnectorsBios Recovery procedure Internal connectors Auxilliary connector 4-pin AUX Important notes on Serial ATA Serial ATA connectors 7-pin SATA1, SATA2Ieee 1394 connector 10-1 pin IE13941 CPU and Chassis Fan Connectors 3-pin CPUFAN1, CHAFAN1Front panel audio connector 10-1 pin Fpaudio ATX power connectors 20-pin ATXPOWER1, 4-pin ATX12VUSB headers 10-1 pin USB56, USB78 System Power LED Lead 3-1 pin Pled System panel connector 20-pin PANEL1ATX Power Switch / Soft-Off Switch Lead 2-pin Pwrsw Reset Switch Lead 2-pin ResetProduct Introduction Bios information Creating a bootable floppy disk Managing and updating your BiosUsing Afudos to update the Bios Using Afudos to copy the current BiosAfudos /ifilename.rom To update the Bios using Asus EZ Flash Using Asus EZ Flash to update the BiosBIOSSetupprogram Bios menu screen Menu items System Time MainmenuSystem Date Day xx/xx/xxxx Legacy Diskette a 1.44M, 3.5Primary/Secondary IDE Master/Slave Acoustic Management Disabled 32Bit Data Transfer DisabledSystem Information Smart Monitoring AutoAdvancedmenu CPU ConfigurationCRC Flood Enable Disabled HT Tristate Enable DisabledHT Frequency 800 MHz HT Data Width Upstream 16 BITMemclock Mode Auto Memory ConfigurationBank Interleaving Auto CAS Latency CL Auto Data Cache BG Scrub Disabled L2 Cache BG Scrub DisabledChipset Cool N’ Quiet EnabledAGP Fast Write Enabled AGP Mode AGPPrimary Graphics Adapter AGP Search for MDA Resources NoMPS Revision PCI Delay Transaction DisabledUSB 2.0 Controller Enabled USB 1.1 Ports Configuration USB 8 PortsUSB 2.0 Controller Mode HiSpeed Legacy USB Support AutoOnboard Devices Configuration Parallel Port IRQ IRQ7 Parallel Port Mode NormalPCIPnP Powermenu APM Configuration Hard Disk Power Down Mode Enabled Video Power Down Mode SuspendPower On By RTC Alarm Disabled Power On External Modems DisabledHardware Monitor CPU Temperature xxxC/xxxF MB Temperature xxxC/xxxFVcore Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage Boot Device Priority Boot menu1st ~ xxth Boot Device 1st Floppy Drive Boot Settings Configuration Change Supervisor Password Interrupt 19 Capture DisabledSecurity Change User Password User Access Level Full AccessClear User Password Password Check SetupExitmenu Load Setup DefaultsExit & Save Changes Exit & Discard Changes