Asus K8V-F, VIA VT8237, VIA K8T800 manual USB headers 10-1 pin USB56, USB78

Page 32

9.USB headers (10-1 pin USB56, USB78)

If the USB ports on the rear panel are inadequate, two USB headers are available for additional USB ports. The USB headers comply with USB 2.0 specification that supports up to 480 Mbps connection speed. This speed advantage over the conventional 12 Mbps on USB 1.1 allows faster Internet connection, interactive gaming, and simultaneous running of high-speed peripherals.

NEVER connect a 1394 cable to the USB_56 or USB_78 connector. Doing so will damage the motherboard!

USB+5V USB P8- USB P8+ GND NC

USB+5V USB P6- USB P6+ GND NC

USB78

USB56

1

1

K8V-F USB 2.0 Header

USB+5V USB P7- USB P7+ GND

USB+5V USB P5- USB P5+ GND

The USB module is purchased separately.

1-22	Chapter 1: Product introduction

Image 32

Contents Motherboard E1495 First Edition December Contents Bios information ChapterContents Federal Communications Commission Statement Operation safety SafetyinformationElectrical safety Conventions used in this guide Where to find more informationAboutthisguide K8V-Fspecificationsummary CPUBios features Industry standard Manageability Form Factor Chapter Special features WelcomeChannel and digital audio solution Asus EZ Flash BiosIntegrated 10/100 Mbps LAN Hardware information AGP 8X supportOnboard LED Before you proceedMotherboard overview Motherboard layoutPlacement direction Screw holesInstalling the CPU Central Processing Unit CPUAngle Overview Memory configuratinsSystem memory Installing a Dimm Removing a DimmExpansion slots Installing an expansion cardConfiguring an expansion card Standard interrupt assignments IRQ assignments for this motherboardPCI slots AGP slotClear RTC RAM CLRTC1 Keyboard power 3-pin KBPWR1Jumpers K8V-F Keyboard Power Setting Bios Recovery procedure ConnectorsRear panel connectors Internal connectors Auxilliary connector 4-pin AUX Serial ATA connectors 7-pin SATA1, SATA2 Important notes on Serial ATACPU and Chassis Fan Connectors 3-pin CPUFAN1, CHAFAN1 Ieee 1394 connector 10-1 pin IE13941ATX power connectors 20-pin ATXPOWER1, 4-pin ATX12V Front panel audio connector 10-1 pin FpaudioUSB headers 10-1 pin USB56, USB78 System panel connector 20-pin PANEL1 System Power LED Lead 3-1 pin PledATX Power Switch / Soft-Off Switch Lead 2-pin Pwrsw Reset Switch Lead 2-pin ResetProduct Introduction Bios information Managing and updating your Bios Creating a bootable floppy diskUsing Afudos to copy the current Bios Using Afudos to update the BiosAfudos /ifilename.rom Using Asus EZ Flash to update the Bios To update the Bios using Asus EZ FlashBIOSSetupprogram Bios menu screen Menu items Mainmenu System TimeSystem Date Day xx/xx/xxxx Legacy Diskette a 1.44M, 3.5Primary/Secondary IDE Master/Slave 32Bit Data Transfer Disabled Acoustic Management DisabledSystem Information Smart Monitoring AutoCPU Configuration AdvancedmenuHT Tristate Enable Disabled CRC Flood Enable DisabledHT Frequency 800 MHz HT Data Width Upstream 16 BITBank Interleaving Auto Memory ConfigurationMemclock Mode Auto CAS Latency CL Auto L2 Cache BG Scrub Disabled Data Cache BG Scrub DisabledCool N’ Quiet Enabled ChipsetAGP Mode AGP AGP Fast Write EnabledPrimary Graphics Adapter AGP Search for MDA Resources NoPCI Delay Transaction Disabled MPS RevisionUSB 1.1 Ports Configuration USB 8 Ports USB 2.0 Controller EnabledUSB 2.0 Controller Mode HiSpeed Legacy USB Support AutoOnboard Devices Configuration Parallel Port Mode Normal Parallel Port IRQ IRQ7PCIPnP Powermenu APM Configuration Video Power Down Mode Suspend Hard Disk Power Down Mode EnabledPower On By RTC Alarm Disabled Power On External Modems DisabledVcore Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage CPU Temperature xxxC/xxxF MB Temperature xxxC/xxxFHardware Monitor 1st ~ xxth Boot Device 1st Floppy Drive Boot menuBoot Device Priority Boot Settings Configuration Security Interrupt 19 Capture DisabledChange Supervisor Password User Access Level Full Access Change User PasswordClear User Password Password Check SetupLoad Setup Defaults ExitmenuExit & Save Changes Exit & Discard Changes