Asus VIA K8T800 Mainmenu, System Time, System Date Day xx/xx/xxxx, Legacy Diskette a 1.44M, 3.5

Page 43

2.3Mainmenu

When you enter the BIOS Setup program, the Main menu screen appears giving you an overview of the basic system information.

Refer to section “2.2.1 BIOS menu screen” for information on the menu screen items and how to navigate through them.

System Time

[11:10:19]

Use [ENTER], [TAB] or

System Time

[11:10:19]

Use [ENTER], [TAB] or

System Date

[Thu, 09/27/2003]

[SHIFT-TAB] to select a

System Date

[Thu, 09/27/2003]

[SHIFT-TAB] to select a

Legacy Diskette A

[1.44M, 3.5 in.]

field.

Legacy Diskette A

[1.44M, 3.5 in.]

field.

Primary IDE Master

[ST321122A]

Use [+] or [-] to

Primary IDE Master

[ST321122A]

Use [+] or [-] to

Primary IDE Slave

[ASUS CDS520/]

configure system time.

Primary IDE Slave

[ASUS CDS520/]

configure system time.

Secondary IDE Master

[Not Detected]

 

Secondary IDE Master

[Not Detected]

 

Secondary IDE Slave

[Not Detected]

 

Secondary IDE Slave

[Not Detected]

 

System Information

 

 

System Information

 

 

2.3.1 System Time [xx:xx:xxxx]

This item allows you to set the system time.

2.3.2 System Date [Day xx/xx/xxxx]

This item allows you to set the system date.

2.3.3 Legacy Diskette A [1.44M, 3.5 in.]

Sets the type of floppy drive installed. Configuration options: [Disabled] [360K, 5.25 in.] [1.2M , 5.25 in.] [720K , 3.5 in.] [1.44M, 3.5 in.] [2.88M, 3.5 in.]

ASUS K8V-F motherboard user guide

2-9

Image 43
Contents Motherboard E1495 First Edition December Contents Chapter Bios informationContents Federal Communications Commission Statement Electrical safety SafetyinformationOperation safety Aboutthisguide Where to find more informationConventions used in this guide CPU K8V-FspecificationsummaryBios features Industry standard Manageability Form Factor Chapter Welcome Special featuresHardware information AGP 8X support Channel and digital audio solutionAsus EZ Flash Bios Integrated 10/100 Mbps LANBefore you proceed Onboard LEDMotherboard layout Motherboard overviewScrew holes Placement directionCentral Processing Unit CPU Installing the CPUAngle System memory Memory configuratinsOverview Removing a Dimm Installing a DimmConfiguring an expansion card Installing an expansion cardExpansion slots IRQ assignments for this motherboard Standard interrupt assignmentsAGP slot PCI slotsJumpers Keyboard power 3-pin KBPWR1Clear RTC RAM CLRTC1 K8V-F Keyboard Power Setting Rear panel connectors ConnectorsBios Recovery procedure Internal connectors Auxilliary connector 4-pin AUX Important notes on Serial ATA Serial ATA connectors 7-pin SATA1, SATA2Ieee 1394 connector 10-1 pin IE13941 CPU and Chassis Fan Connectors 3-pin CPUFAN1, CHAFAN1Front panel audio connector 10-1 pin Fpaudio ATX power connectors 20-pin ATXPOWER1, 4-pin ATX12VUSB headers 10-1 pin USB56, USB78 Reset Switch Lead 2-pin Reset System panel connector 20-pin PANEL1System Power LED Lead 3-1 pin Pled ATX Power Switch / Soft-Off Switch Lead 2-pin PwrswProduct Introduction Bios information Creating a bootable floppy disk Managing and updating your BiosUsing Afudos to update the Bios Using Afudos to copy the current BiosAfudos /ifilename.rom To update the Bios using Asus EZ Flash Using Asus EZ Flash to update the BiosBIOSSetupprogram Bios menu screen Menu items Legacy Diskette a 1.44M, 3.5 MainmenuSystem Time System Date Day xx/xx/xxxxPrimary/Secondary IDE Master/Slave Smart Monitoring Auto 32Bit Data Transfer DisabledAcoustic Management Disabled System InformationAdvancedmenu CPU ConfigurationHT Data Width Upstream 16 BIT HT Tristate Enable DisabledCRC Flood Enable Disabled HT Frequency 800 MHzMemclock Mode Auto Memory ConfigurationBank Interleaving Auto CAS Latency CL Auto Data Cache BG Scrub Disabled L2 Cache BG Scrub DisabledChipset Cool N’ Quiet EnabledSearch for MDA Resources No AGP Mode AGPAGP Fast Write Enabled Primary Graphics Adapter AGPMPS Revision PCI Delay Transaction DisabledLegacy USB Support Auto USB 1.1 Ports Configuration USB 8 PortsUSB 2.0 Controller Enabled USB 2.0 Controller Mode HiSpeedOnboard Devices Configuration Parallel Port IRQ IRQ7 Parallel Port Mode NormalPCIPnP Powermenu APM Configuration Power On External Modems Disabled Video Power Down Mode SuspendHard Disk Power Down Mode Enabled Power On By RTC Alarm DisabledHardware Monitor CPU Temperature xxxC/xxxF MB Temperature xxxC/xxxFVcore Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage Boot Device Priority Boot menu1st ~ xxth Boot Device 1st Floppy Drive Boot Settings Configuration Change Supervisor Password Interrupt 19 Capture DisabledSecurity Password Check Setup User Access Level Full AccessChange User Password Clear User PasswordExit & Discard Changes Load Setup DefaultsExitmenu Exit & Save Changes