Asus K8V-F, VIA VT8237, VIA K8T800 manual MPS Revision, PCI Delay Transaction Disabled

Page 53

SouthBridge Configuration

MPS	Revision	[1.4]
PCI	Delay Transaction	[Disabled]

MPS Revision [1.4]

This item sets the MPS revision value. Configuration options: [1.1] [1.4]

PCI Delay Transaction [Disabled]

This item enables or disables the PCI Delay transaction feature. Configuration options: [Disabled] [Enabled]

USB Configuration

USB Configuration	Enabled/Disabled AMD k8
Module Version - 2.23.0-7.4	Cool N’Quiet function.
Module Version - 2.23.0-7.4
USB Devices Enabled :
None
USB 1.1 Ports Configuration	[8 USB Ports]
USB 2.0 Controller	[Enabled]
Legacy USB Support	[Auto]
USB 2.0 Controller Mode	[HiSpeed]

The Module Version and USB Devices Enabled items show the auto-detected values. If no USB device is detected, the item shows None.

ASUS K8V-F motherboard user guide

2-19

Image 53

Contents Motherboard E1495 First Edition December Contents Chapter Bios informationContents Federal Communications Commission Statement Operation safety SafetyinformationElectrical safety Conventions used in this guide Where to find more informationAboutthisguide CPU K8V-FspecificationsummaryBios features Industry standard Manageability Form Factor Chapter Welcome Special featuresAsus EZ Flash Bios Channel and digital audio solutionIntegrated 10/100 Mbps LAN Hardware information AGP 8X supportBefore you proceed Onboard LEDMotherboard layout Motherboard overviewScrew holes Placement directionCentral Processing Unit CPU Installing the CPUAngle Overview Memory configuratinsSystem memory Removing a Dimm Installing a DimmExpansion slots Installing an expansion cardConfiguring an expansion card IRQ assignments for this motherboard Standard interrupt assignmentsAGP slot PCI slotsClear RTC RAM CLRTC1 Keyboard power 3-pin KBPWR1Jumpers K8V-F Keyboard Power Setting Bios Recovery procedure ConnectorsRear panel connectors Internal connectors Auxilliary connector 4-pin AUX Important notes on Serial ATA Serial ATA connectors 7-pin SATA1, SATA2Ieee 1394 connector 10-1 pin IE13941 CPU and Chassis Fan Connectors 3-pin CPUFAN1, CHAFAN1Front panel audio connector 10-1 pin Fpaudio ATX power connectors 20-pin ATXPOWER1, 4-pin ATX12VUSB headers 10-1 pin USB56, USB78 System Power LED Lead 3-1 pin Pled System panel connector 20-pin PANEL1ATX Power Switch / Soft-Off Switch Lead 2-pin Pwrsw Reset Switch Lead 2-pin ResetProduct Introduction Bios information Creating a bootable floppy disk Managing and updating your BiosUsing Afudos to update the Bios Using Afudos to copy the current BiosAfudos /ifilename.rom To update the Bios using Asus EZ Flash Using Asus EZ Flash to update the BiosBIOSSetupprogram Bios menu screen Menu items System Time MainmenuSystem Date Day xx/xx/xxxx Legacy Diskette a 1.44M, 3.5Primary/Secondary IDE Master/Slave Acoustic Management Disabled 32Bit Data Transfer DisabledSystem Information Smart Monitoring AutoAdvancedmenu CPU ConfigurationCRC Flood Enable Disabled HT Tristate Enable DisabledHT Frequency 800 MHz HT Data Width Upstream 16 BITBank Interleaving Auto Memory ConfigurationMemclock Mode Auto CAS Latency CL Auto Data Cache BG Scrub Disabled L2 Cache BG Scrub DisabledChipset Cool N’ Quiet EnabledAGP Fast Write Enabled AGP Mode AGPPrimary Graphics Adapter AGP Search for MDA Resources NoMPS Revision PCI Delay Transaction DisabledUSB 2.0 Controller Enabled USB 1.1 Ports Configuration USB 8 PortsUSB 2.0 Controller Mode HiSpeed Legacy USB Support AutoOnboard Devices Configuration Parallel Port IRQ IRQ7 Parallel Port Mode NormalPCIPnP Powermenu APM Configuration Hard Disk Power Down Mode Enabled Video Power Down Mode SuspendPower On By RTC Alarm Disabled Power On External Modems DisabledVcore Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage CPU Temperature xxxC/xxxF MB Temperature xxxC/xxxFHardware Monitor 1st ~ xxth Boot Device 1st Floppy Drive Boot menuBoot Device Priority Boot Settings Configuration Security Interrupt 19 Capture DisabledChange Supervisor Password Change User Password User Access Level Full AccessClear User Password Password Check SetupExitmenu Load Setup DefaultsExit & Save Changes Exit & Discard Changes