Canon DU7-1175-000 service manual

Page 27

E.Once all “8” mounting screws have been properly started you have good alignment. You may now go back and tighten the screws until they are snug. Do not over tighten the “2” screws on top!

Step 16: Install the “2” Screws to secure the Bearing Block for the Pulley arrangement at the rear of the Professional Puncher-A1. Press the block to the top of the punch before tightening

Step 17: Install the Pulley and Belt onto the Pulley Block. Once properly aligned, check Belt and Pulley movement. Tighten the Set Screw.

Step 18: Install the Die Set Storage Rack with “3” screws front and “3” screws back. Remember to attach the Ground Strap at the middle screw on the rear (belt side). Start each screw to achieve proper alignment, then go back over each screw and tighten it.

Step 19: Install the Cable Guard on top of the Die Set Storage Rack (“2” Screws).

Step 20: Install the curved sheet metal Exit Paper Guide with Idler Roller “4” Screws.

Start all “4” screws, (2 on front and 2 on back) then tighten.

Step 21: Connect the Sensor Wire Harness at the top rear of the Exit Paper Guide.

Step 22: To install the Idler Aligner Paper Guide.

A.Hold it loosely in place.

B.Press the Nylon Flange Bearings into place, through both pieces of sheet metal, with the Flange to the inside.

C.Slide the Shaft through the front of the machine, while holding the Nylon Flange Bearing in place.

D.Secure with “2” E-Rings on the inside of the bearing.

E.Inspect by pressing in on the bottom area of the sheet metal for: #1 should see a slight deflection of each Idler Roller as you press, #2 as you press, you can turn the Pulley’s at the rear of the Professional Puncher-A1 and see the Idler Rollers rotate smoothly.

Step 23: Bend the small metal tab back into place.

Step 24: Install the J2 Shaft back into place by inserting it first into the front, then the back.

Step 25: Close the J2 Flipper Latch.

Repeat the test of rotating the pulleys to ensure smooth rotation of the Idler Rollers.

Step 26: Attach the J2 Shaft Spring

Install the front E-Ring to secure J2.

Step 27: Attach the Docking Plate using “4” Screws and install spring from Plate to Door.

Step 28: Attach the Back Rear Cover using the 7 screws (2 for the Entrance and 5 for the Exit side).

Test the Professional Puncher-A1 by running 10 copies in bypass mode,

Then 1 sheet in punch mode, Then 10 sheets in punch mode, Then 100 sheets in punch model

27

Image 27
Contents Professional Puncher-A1 Table of Contents Professional PUNCHER-A1 FAQ’S IntroductionIntroduction X 11 LEF Only Die SetsPunch Pattern Samples North America Letter Shown Unit Operation InstallationUnpacking Unit SET-UPFelt PAD Magnet Sheild Shoulder Bolt With Spring INSPECTION, Cleaning and Lubrication MaintenanceDIE SET Maintenance Preventative Maintenance Schedule Setting the Right ExpectationsProduct Positioning Adjustment and Special Procedures DIE SET Position Cradle ADJUSTMENT, Centering Punched HolesTool Recommendations Punched Hole Alignment Checking Turn Counter Clockwise Removal of Punch Module Cause Green Belt REPLACEMENT, Aligner Panel REMOVAL, ExplanationSymptom Paper will stop moving through the Punch paper pathGreen Belt REPLACEMENT, Paper Entrance Side Procedure to Replace Aligner BeltsFC3-3633-0000 Binder Side Page Stretch Sensor Flexible Shaft Align & FIX Screws Instal J2 Shaft Green Belt REPLACEMENT, Paper Exit Side Binder Side Paper Enterance Aligner Drive Belt Assy Assembly Process Assemble Back Page General Description Installation StepsBack Gauge Assy Front Side To Clear a Paper JAM Software Update Procedure Version Tools Required Software Update Procedure VersionBootloaderg COM5 Outputs Technical TroubleshootingTheory of Operation InputsPunch Control General TroubleshootingSerial Eeprom Control Stepper #1 ControlPage Symptom Probable Cause Corrective Action Troubleshooting Guide ChartPage OUBLRevHOOTING Guide Chart Operating Controls Punching PatternsChanging the Punch DIE Sets Step Paper Chip DrawerService Problem SOLVING, Operator Level Professional PUNCHER-A1Problem Probable Cause SPECIFICATIONS, 208V & 230/240V Professional PUNCHER-A1 Specifications